Video & Articles: Appliance & Equipment RepairDispenser Water Line (part 218976409 ) - Frigidaire Refrigerator Repair Help

Dispenser Water Line (part 218976409 ) - Frigidaire Refrigerator Repair Help

04:30
This video provides step-by-step repair instructions for replacing the dispenser water line on a Frigidaire refrigerator (Model FFSS2315TS0). The most common reason for replacing the dispenser water line is when the refrigerator ice maker is not working.

All of the information for this refrigerator dispenser water line replacement video is applicable to the following brands:
Frigidaire, White Westinghouse, Kelvinator, Gibson, Kenmore, Tappan, & Electrolux.

Tools used: Phillips-head screwdriver, number two square drive bit, & a 7/16th inch wrench.

Step By Step Instructions

1
Frigidaire Refrigerator - Model FFSS2315TS0
2
Refrigerator Dispenser Water Line Replacement
3
Tools Needed
4
You will need a phillips-head screwdriver, a 7/16th inch wrench and a quarter-inch socket or nut driver for this procedure.
5
Shock
6
Be sure to unplug the power cord.
7
Remove the drip tray, then use a phillips-head screwdriver to unthread the three lower screws securing the front dispenser panel.
8
Slide the panel up to detach, then disconnect the wire connecter.
9
Using the phillips-head screwdriver or a number two square drive bit, unthread the three screws securing the module.
10
Slide out the dispenser water line and disconnect the wire connecter to move the module out of the way.
11
Detach the lower grille.
12
Water
13
Use a 7/16th inch wrench to depress the retaining ring to release the water line from the coupler.
14
Cut the tape securing the water line spring and slide the spring off.
15
You can now fully remove the old line.
16
Install the new dispenser water line by feeding it through the bottom of the freezer door until it appears in the dispenser housing.
17
Position the spring approximately two inches from the end of the line, then use tape to secure the spring.
18
Now insert the end of the dispenser water line through the hole in the module.
19
Connect the wire connecter and fully reposition the module.
20
Thread the screws to secure.
21
Reinstall the front panel by first connecting the wire connecter.
22
Align the tabs with the slots in the door and slide down.
23
Rethread the lower screws.
24
Replace the drip tray.
25
Insert the end of the water line into the coupler until fully seated.
26
Realign the grille and snap it into place.
27
Plug the power cord back in.
28
Congrats! Your refrigerator is now ready for use.
Description
This video provides step-by-step repair instructions for replacing the dispenser water line on a Frigidaire refrigerator (Model FFSS2315TS0). The most common reason for replacing the dispenser water line is when the refrigerator ice maker is not working.

All of the information for this refrigerator dispenser water line replacement video is applicable to the following brands:
Frigidaire, White Westinghouse, Kelvinator, Gibson, Kenmore, Tappan, & Electrolux.

Tools used: Phillips-head screwdriver, number two square drive bit, & a 7/16th inch wrench.
Step-By-Step Instructions
1
Frigidaire Refrigerator - Model FFSS2315TS0
2
Refrigerator Dispenser Water Line Replacement
3
Tools Needed
4
You will need a phillips-head screwdriver, a 7/16th inch wrench and a quarter-inch socket or nut driver for this procedure.
5
Shock
6
Be sure to unplug the power cord.
7
Remove the drip tray, then use a phillips-head screwdriver to unthread the three lower screws securing the front dispenser panel.
8
Slide the panel up to detach, then disconnect the wire connecter.
9
Using the phillips-head screwdriver or a number two square drive bit, unthread the three screws securing the module.
10
Slide out the dispenser water line and disconnect the wire connecter to move the module out of the way.
11
Detach the lower grille.
12
Water
13
Use a 7/16th inch wrench to depress the retaining ring to release the water line from the coupler.
14
Cut the tape securing the water line spring and slide the spring off.
15
You can now fully remove the old line.
16
Install the new dispenser water line by feeding it through the bottom of the freezer door until it appears in the dispenser housing.
17
Position the spring approximately two inches from the end of the line, then use tape to secure the spring.
18
Now insert the end of the dispenser water line through the hole in the module.
19
Connect the wire connecter and fully reposition the module.
20
Thread the screws to secure.
21
Reinstall the front panel by first connecting the wire connecter.
22
Align the tabs with the slots in the door and slide down.
23
Rethread the lower screws.
24
Replace the drip tray.
25
Insert the end of the water line into the coupler until fully seated.
26
Realign the grille and snap it into place.
27
Plug the power cord back in.
28
Congrats! Your refrigerator is now ready for use.

Applicable Product Model

Refrigerator
Brand
Product Type
Model
Subtype
Cooling System
Icemaking System
Dispensing System
Product Diagram & Manuals
Parts Needed
Total$0.00

Related Articles & Videos

01:40
Part Replacement
Icemaker (part 241798231) - Frigidaire Refrigerator Repair Help
02:52
Part Replacement
Lower Refrigerator Door Hinge (part 242034601) - Frigidaire Refrigerator Repair Help
03:22
Part Replacement
Refrigerator Air Damper Assembly (part 242303001) - Frigidaire Refrigerator Repair Help
03:10
Part Replacement
Refrigerator Light Socket (part 218906802) - Frigidaire Refrigerator Repair Help
03:28
Part Replacement
Freezer Light Socket (part 241559801) - Frigidaire Refrigerator Repair Help