In-stock parts ship the same day
Price Match Guarantee
In-stock parts ship the same dayGET PRO PRICING
Video & Articles: Appliance & Equipment RepairHonda Small Engine Primer Bulb Replacement #16032-ZM3-004
Honda Small Engine Primer Bulb Replacement #16032-ZM3-004
Total Parts Cost
$NaN03:30
- Description
This video provides step-by-step repair instructions for replacing the primer bulb on a Honda small engine. The most common reasons for replacing the primer bulb are when the engine leaks gas or won’t start.
All of the information for this primer bulb replacement video is applicable to the following brands:
Honda
Tools needed: 8mm socket or nut driver, small flat-head screwdriver, Phillips-head screwdriver
All of the information for this primer bulb replacement video is applicable to the following brands:
Honda
Tools needed: 8mm socket or nut driver, small flat-head screwdriver, Phillips-head screwdriver
Step By Step Instructions
1
Before you replace the primer bulb on your engine’s carburetor first make sure the engine has cooled.
2
Now depress the tabs to release the air filter cover and pull out the filter element.
3
Use an 8mm socket or nut driver to unthread the mounting nuts securing the filter housing.
4
Remove the support plate and detach the housing from the breather tube.
5
Note the orientation of the fuel lines attached to the carburetor then detach them – be prepared for some fuel to spill out.
6
With the lines detached, slide the carburetor off of the mounting posts. and set it on a sturdy surface.
7
Use a phillips-head screwdriver to remove the screws holding the carburetor components together.
8
Carefully lift off the mounting plate and remove the old primer bulb if still intact.
9
Install the new primer bulb by inserting it into the mounting plate.
10
Realign the plate then thread and tighten the screws to secure.
11
Confirm that the mounting posts are fully extended and slide the carburetor onto them.
12
Attach the fuel lines to the appropriate ports on the carburetor.
13
Confirm that the O-ring is in place on the air filter housing then reposition the housing by inserting the port into the breather tube as you align the housing on the posts.
14
Replace the support plate then thread and tighten the mounting nuts to secure the assembly.
15
Replace the air filter element.
16
Realign the air filter cover and snap it into place.
Description
This video provides step-by-step repair instructions for replacing the primer bulb on a Honda small engine. The most common reasons for replacing the primer bulb are when the engine leaks gas or won’t start.
All of the information for this primer bulb replacement video is applicable to the following brands:
Honda
Tools needed: 8mm socket or nut driver, small flat-head screwdriver, Phillips-head screwdriver
All of the information for this primer bulb replacement video is applicable to the following brands:
Honda
Tools needed: 8mm socket or nut driver, small flat-head screwdriver, Phillips-head screwdriver
Step-By-Step Instructions
1
Before you replace the primer bulb on your engine’s carburetor first make sure the engine has cooled.
2
Now depress the tabs to release the air filter cover and pull out the filter element.
3
Use an 8mm socket or nut driver to unthread the mounting nuts securing the filter housing.
4
Remove the support plate and detach the housing from the breather tube.
5
Note the orientation of the fuel lines attached to the carburetor then detach them – be prepared for some fuel to spill out.
6
With the lines detached, slide the carburetor off of the mounting posts. and set it on a sturdy surface.
7
Use a phillips-head screwdriver to remove the screws holding the carburetor components together.
8
Carefully lift off the mounting plate and remove the old primer bulb if still intact.
9
Install the new primer bulb by inserting it into the mounting plate.
10
Realign the plate then thread and tighten the screws to secure.
11
Confirm that the mounting posts are fully extended and slide the carburetor onto them.
12
Attach the fuel lines to the appropriate ports on the carburetor.
13
Confirm that the O-ring is in place on the air filter housing then reposition the housing by inserting the port into the breather tube as you align the housing on the posts.
14
Replace the support plate then thread and tighten the mounting nuts to secure the assembly.
15
Replace the air filter element.
16
Realign the air filter cover and snap it into place.
Applicable Product Model
Related Articles & Videos