Order by 9:00 p.m., and we'll ship the same day
Price Match Guarantee
Order by 9:00 p.m., and we'll ship the same dayGET PRO PRICING
Video & Articles: Appliance & Equipment RepairGE Washer Speed Sensor Replacement WH12X26330
This video provides step-by-step repair instructions for replacing the speed sensor in a GE washer (Model GTW465ASN2WW). The most common reason for replacing this part is if it's missing or broken.
This replacement video is applicable to the following brands:
GE
Screws affiliated with washer-
Don't forget to like and comment on this video and subscribe to our channel!
GE Washer Speed Sensor Replacement WH12X26330
Skill Level
Total Parts Cost
$30.12Estimated Savings
$112.5004:52
- Description
This video provides step-by-step repair instructions for replacing the speed sensor in a GE washer (Model GTW465ASN2WW). The most common reason for replacing this part is if it's missing or broken.
This replacement video is applicable to the following brands:
GE
Screws affiliated with washer-
Don't forget to like and comment on this video and subscribe to our channel!
Step By Step Instructions
1
To replace the speed sensor in your ge washer, you will need an impact driver with a 1/4” bit, pliers, a 3/8” socket, a 14mm socket, a pick, a flathead screwdriver, a 1/4" to 3/8” socket adapter, and a 1/4” socket adapter.
2
Before you begin the procedure, unplug the power to the washer.
3
Shut off the water supply
4
Remove the drain line from the wall
5
Remove the hot and cold-water supply lines from the inlet valve…
6
Prop up the washer. you can use a wooden block or chair.
7
Unthread the three screws on the protective belt cover to remove it.
8
Using the 14mm socket, unthread the nut.
9
Pull the belt off of the big pulley first then remove it.
10
Remove the pulley off the shaft.
11
Using the flathead screwdriver, apply outward pressure on the speed sensor while using the pick to undo the holding tabs, then slide the sensor off.
12
Pull up on the red safety tab to unlock the speed sensor connector then unplug it.
13
To install the new speed sensor, plug in the speed sensor and push down on the red tab to lock the connector.
14
Slide the speed sensor over the motor frame and press to snap in place.
15
Slide the pulley on the shaft and line it up with the splines, then thread the nut onto the shaft. while tightening, the pulley will seat into position.
16
Place the belt ribside facing inward over the big pulley then stretch the belt over the small pulley.
17
Rotate the pulleys to align the belt properly.
18
Align the cover and start one of the three screws.
19
Place the grounding connector over the screw and rethread it to the bottom of the transmission.
20
Now rethread the last screw.
21
Prop up the washer.
22
Reattatch the hot and cold-water supply lines.
23
Insert the drain hose back into the wall drain.
24
Turn on the water supply
25
Plug in the power.
Description
This video provides step-by-step repair instructions for replacing the speed sensor in a GE washer (Model GTW465ASN2WW). The most common reason for replacing this part is if it's missing or broken.
This replacement video is applicable to the following brands:
GE
Screws affiliated with washer-
Don't forget to like and comment on this video and subscribe to our channel!
This video provides step-by-step repair instructions for replacing the speed sensor in a GE washer (Model GTW465ASN2WW). The most common reason for replacing this part is if it's missing or broken.
This replacement video is applicable to the following brands:
GE
Screws affiliated with washer-
Don't forget to like and comment on this video and subscribe to our channel!
Step-By-Step Instructions
1
To replace the speed sensor in your ge washer, you will need an impact driver with a 1/4” bit, pliers, a 3/8” socket, a 14mm socket, a pick, a flathead screwdriver, a 1/4" to 3/8” socket adapter, and a 1/4” socket adapter.
2
Before you begin the procedure, unplug the power to the washer.
3
Shut off the water supply
4
Remove the drain line from the wall
5
Remove the hot and cold-water supply lines from the inlet valve…
6
Prop up the washer. you can use a wooden block or chair.
7
Unthread the three screws on the protective belt cover to remove it.
8
Using the 14mm socket, unthread the nut.
9
Pull the belt off of the big pulley first then remove it.
10
Remove the pulley off the shaft.
11
Using the flathead screwdriver, apply outward pressure on the speed sensor while using the pick to undo the holding tabs, then slide the sensor off.
12
Pull up on the red safety tab to unlock the speed sensor connector then unplug it.
13
To install the new speed sensor, plug in the speed sensor and push down on the red tab to lock the connector.
14
Slide the speed sensor over the motor frame and press to snap in place.
15
Slide the pulley on the shaft and line it up with the splines, then thread the nut onto the shaft. while tightening, the pulley will seat into position.
16
Place the belt ribside facing inward over the big pulley then stretch the belt over the small pulley.
17
Rotate the pulleys to align the belt properly.
18
Align the cover and start one of the three screws.
19
Place the grounding connector over the screw and rethread it to the bottom of the transmission.
20
Now rethread the last screw.
21
Prop up the washer.
22
Reattatch the hot and cold-water supply lines.
23
Insert the drain hose back into the wall drain.
24
Turn on the water supply
25
Plug in the power.
Applicable Product Model
Related Articles & Videos