Order by 2:00 a.m., and we'll ship the same day
Price Match Guarantee
Order by 2:00 a.m., and we'll ship the same dayGET PRO PRICING
Video & Articles: Appliance & Equipment RepairElectrolux Dishwasher Rear Leveling Leg Replacement 117363200 
Electrolux Dishwasher Rear Leveling Leg Replacement 117363200
Skill Level
Total Parts Cost
$84.51Estimated Savings
$112.5006:57
- Description
This video provides step-by-step instructions for replacing the rear leveling leg on Electrolux dishwashers.
All of the information in this video is applicable to the following brands: Electrolux
All of the information in this video is applicable to the following brands: Electrolux
Step By Step Instructions
1
Electrolux Dishwasher - 24ID75SPS3A
2
2, 1, 3",Dishwasher Rear Leveling Leg Replacement
3
Turn off the power to the appliance
4
Shut off the water supply valve
5
You will need a phillips-head screwdriver and channel-lock pliers
6
Use the phillips-head screwdriver to unthread the two mounting screws securing the lower access panel
7
Set the panel aside
8
Use channel-lock pliers to loosen the elbow fitting securing the water supply line to the inlet valve
9
Detach the strain relief and cord from the junction
10
Remove the support
11
Tip the appliance back and rest it on the rear panel
12
Release the tab to detach the rear leg adjusting rod
13
"Using pliers, squeeze the retaining clips to release the bottom panel"
14
Rotate the old rear leg clockwise to remove
15
Align the adjusting cog with the flat side facing outward
16
Thread the new leg in counter-clockwise--keeping the foot close to the base
17
Align the bottom panel tabs with the slots in the base and snap the panel in place
18
Insert the bottom of the adjusting rod into the hole in the base and snap the upper portion in place
19
Return the dishwasher to its upright position
20
"Fully position the power supply cord and strain relief in the junction box, then thread and tighten the nut"
21
"Join the black wires together, the white wires together, and the green wires together, securing them with wire nuts"
22
Realign the cover and rethread the screw
23
Confirm that the end of the drain hose is accessible through the cabinet wall and the water supply line is positioned in the channel in the base
24
Gently slide the dishwasher back into the cabinet
25
Rotate the adjusting rod clockwise to extend the rear leg
26
Rethread the screws to secure the mounting brackets to the cabinet or countertop
27
Feed the drain hose through the cabinet and connect it to the sink drain or disposer
28
Make sure the hose is elevated above the connection point
29
Thread the water supply line elbow fitting onto the inlet valve port and tighten
30
Realign the lower access panel and rethread the screws to secure
31
Turn the water and power back on for the appliance
Description
This video provides step-by-step instructions for replacing the rear leveling leg on Electrolux dishwashers.
All of the information in this video is applicable to the following brands: Electrolux
All of the information in this video is applicable to the following brands: Electrolux
Step-By-Step Instructions
1
Electrolux Dishwasher - 24ID75SPS3A
2
2, 1, 3",Dishwasher Rear Leveling Leg Replacement
3
Turn off the power to the appliance
4
Shut off the water supply valve
5
You will need a phillips-head screwdriver and channel-lock pliers
6
Use the phillips-head screwdriver to unthread the two mounting screws securing the lower access panel
7
Set the panel aside
8
Use channel-lock pliers to loosen the elbow fitting securing the water supply line to the inlet valve
9
Detach the strain relief and cord from the junction
10
Remove the support
11
Tip the appliance back and rest it on the rear panel
12
Release the tab to detach the rear leg adjusting rod
13
"Using pliers, squeeze the retaining clips to release the bottom panel"
14
Rotate the old rear leg clockwise to remove
15
Align the adjusting cog with the flat side facing outward
16
Thread the new leg in counter-clockwise--keeping the foot close to the base
17
Align the bottom panel tabs with the slots in the base and snap the panel in place
18
Insert the bottom of the adjusting rod into the hole in the base and snap the upper portion in place
19
Return the dishwasher to its upright position
20
"Fully position the power supply cord and strain relief in the junction box, then thread and tighten the nut"
21
"Join the black wires together, the white wires together, and the green wires together, securing them with wire nuts"
22
Realign the cover and rethread the screw
23
Confirm that the end of the drain hose is accessible through the cabinet wall and the water supply line is positioned in the channel in the base
24
Gently slide the dishwasher back into the cabinet
25
Rotate the adjusting rod clockwise to extend the rear leg
26
Rethread the screws to secure the mounting brackets to the cabinet or countertop
27
Feed the drain hose through the cabinet and connect it to the sink drain or disposer
28
Make sure the hose is elevated above the connection point
29
Thread the water supply line elbow fitting onto the inlet valve port and tighten
30
Realign the lower access panel and rethread the screws to secure
31
Turn the water and power back on for the appliance
Applicable Product Model
Related Articles & Videos