Order by 2:00 a.m., and we'll ship the same day
Price Match Guarantee
Order by 2:00 a.m., and we'll ship the same dayGET PRO PRICING
Video & Articles: Appliance & Equipment RepairFrigidaire Dishwasher User Interface Assembly Replacement (part 5304517587) 
Frigidaire Dishwasher User Interface Assembly Replacement (part 5304517587)
Skill Level
Total Parts Cost
$74.49Estimated Savings
$112.5003:50
- Description
This video provides step-by-step repair instructions for replacing the user interface on Frigidaire dishwasher model #FGID2466QF7A.
All of the information for this user interface replacement video is applicable to the following brands: Frigidaire & Electrolux
Tools needed: Phillips-head screwdriver, & a T-20 Torx bit.
All of the information for this user interface replacement video is applicable to the following brands: Frigidaire & Electrolux
Tools needed: Phillips-head screwdriver, & a T-20 Torx bit.
Step By Step Instructions
1
Frigidaire Dishwasher - Model FGID2466QF7A
2
Dishwasher User Interface Assembly Replacement
3
Tools Needed
4
You will need a phillips-head screwdriver and a T-20 Torx bit for this procedure.
5
Be sure to turn off the power to the appliance.
6
Open the door and use a phillips-head screwdriver to unthread all four screws securing the outer door panel.
7
"With the screws unthreaded, you can pull the panel down to detach."
8
"Using a T-20 Torx bit, unthread the six screws securing the control panel assembly."
9
"Using the phillips-head screwdriver, unthread the two screws securing the control board cover."
10
Pull back the retainers to release the cover tab and detach the wiring grommet.
11
"Pull the retaining tabs back to release the two user interface boards, then disconnect the wire harness from the control board."
12
"Install the new user interface assembly by sliding the two boards into place in the control panel, then connect the wire harness."
13
Secure the wires under the retaining clips.
14
Position the wiring grommet in the control board cover then snap the cover into place.
15
Thread the two mounting screws.
16
Realign the control panel assembly and secure it with the screws.
17
Reinstall the outer door panel by aligning it on the inner panel then slide up.
18
Thread the four mounting screws to secure.
19
Turn the power supply back on.
20
Congrats! Your dishwasher is ready for use.
Description
This video provides step-by-step repair instructions for replacing the user interface on Frigidaire dishwasher model #FGID2466QF7A.
All of the information for this user interface replacement video is applicable to the following brands: Frigidaire & Electrolux
Tools needed: Phillips-head screwdriver, & a T-20 Torx bit.
All of the information for this user interface replacement video is applicable to the following brands: Frigidaire & Electrolux
Tools needed: Phillips-head screwdriver, & a T-20 Torx bit.
Step-By-Step Instructions
1
Frigidaire Dishwasher - Model FGID2466QF7A
2
Dishwasher User Interface Assembly Replacement
3
Tools Needed
4
You will need a phillips-head screwdriver and a T-20 Torx bit for this procedure.
5
Be sure to turn off the power to the appliance.
6
Open the door and use a phillips-head screwdriver to unthread all four screws securing the outer door panel.
7
"With the screws unthreaded, you can pull the panel down to detach."
8
"Using a T-20 Torx bit, unthread the six screws securing the control panel assembly."
9
"Using the phillips-head screwdriver, unthread the two screws securing the control board cover."
10
Pull back the retainers to release the cover tab and detach the wiring grommet.
11
"Pull the retaining tabs back to release the two user interface boards, then disconnect the wire harness from the control board."
12
"Install the new user interface assembly by sliding the two boards into place in the control panel, then connect the wire harness."
13
Secure the wires under the retaining clips.
14
Position the wiring grommet in the control board cover then snap the cover into place.
15
Thread the two mounting screws.
16
Realign the control panel assembly and secure it with the screws.
17
Reinstall the outer door panel by aligning it on the inner panel then slide up.
18
Thread the four mounting screws to secure.
19
Turn the power supply back on.
20
Congrats! Your dishwasher is ready for use.
Applicable Product Model
Related Articles & Videos
00:48
Part Replacement
Frigidaire Dishwasher Center Wash Arm Assembly Replacement (part 5304506740)
01:08
Part Replacement
Frigidaire Dishwasher Bottom Tank Gasket Replacement (part 5304500204)
07:11
Part Replacement
Frigidaire Dishwasher Circulation Pump & Motor Replacement (part 154853801)
04:55
Part Replacement
Frigidaire Dishwasher Control Panel Replacement (part 5304520552)