Unlock the Right Part
for Your Repair
Find the exact part you need
Enter your model number to see parts that fit your machine.
Choose Product
Identify Problem
03
Find Solutions
HomeRepair HelpHotpoint Washer RepairHotpoint Washer dispenser not working properly Repair
Hotpoint Washer dispenser not working properly
When your Hotpoint washer dispenser is not working, detergent, bleach, or fabric softener may remain in the drawer or fail to flush into the tub. The most likely cause is low water pressure or a faulty water inlet valve. The valve needs at least 20 psi to supply enough water, so check household water pressure first, then replace the water inlet valve if pressure is adequate. Next, inspect the detergent container for clogs, misalignment, or damage. A blocked or damaged dispenser, drawer, or dispenser compartment can also cause detergent dispenser problems and prevent proper dispensing. Clean any buildup and replace the dispenser or drawer if needed. If your model uses a siphon break, clean the siphon tube and compartment trays because a clog can leave diluted detergent or fabric softener behind. When these parts are working, the control board may not be sending voltage to the dispenser water valves or actuator at the correct time. Use a multimeter to test the circuit before replacing the control board. Enter your Hotpoint washer model number to find the exact replacement part for your specific washing machine.
01 - Hotpoint Washing Machine Dispenser
A washer detergent dispenser not working is often the result of low water pressure in the home or a defective water inlet valve not supplying water to the dispenser. However, it's also possible the dispenser drawer is obstructed or damaged and not allowing the detergent to be dispensed. You should inspect the drawer for any obstructions or damage and replace the component if necessary.
Enter model number to search for the required part specific to your product
Top Solution
02 - Hotpoint Washing Machine Water Inlet Valve
The dispenser uses water from the inlet valve to flush out the detergent and fabric softener from the dispenser. If the water flow is too slow the dispenser will not distribute the detergent and softener properly. The water inlet valve requires at least 20 psi to function properly. First, check the water pressure to determine that it is adequate. If the water pressure is adequate, replace the water inlet valve.
Top Solution
03 - Hotpoint Washing Machine Detergent Container
The dispenser's detergent container could be clogged, misaligned, or damaged, and unable to dispense its contents properly. Inspect the detergent container for any damage and replace if necessary.
Top Solution
04 - Hotpoint Washing Machine Siphon Break
Some dispensers use a siphon tube. If the siphon tube gets plugged you may get a diluted mixture of detergent, bleach, or fabric softener remaining in the tray. Make sure the dispenser compartment trays and siphon tubes are clean.
Highly Likely
05 - Hotpoint Washing Machine Drawer
A washer dispenser not working is often the result of low water pressure in the home or a defective water inlet valve not supplying water to the dispenser. However, it's also possible the dispenser drawer is obstructed or damaged and not allowing the detergent, bleach, or fabric softener to be dispensed. You should inspect the drawer for any obstructions or damage and replace the component if necessary.
Common
06 - Hotpoint Washing Machine Detergent Dispenser
Most washer dispensers use a water inlet valve to move water through the different dispenser compartments at specified times to dispense the soap or fabric softener. Some models use a diverter motor. If the dispenser is clogged and cannot be cleaned or the water inlet valve is part of the dispenser and no water is flowing through it, the dispenser will need to be replaced.
Common
07 - Hotpoint Washing Machine Control Board
A washer detergent dispenser not working is often the result of low water pressure in the home or a defective water inlet valve not supplying water to the dispenser. However, it's also possible the appliance's control board is not sending power to the dispenser water valves or dispenser actuator at the proper times. You can use a multimeter to help determine if voltage is reaching these components. If not, the control board will need to be replaced.
Common
Frequently Asked Questions
Why is my Hotpoint washer not dispensing detergent or fabric softener?
How do I fix a Hotpoint washer detergent tray that is not draining?
Can a clogged dispenser cause my washing machine not to dispense detergent?
How do I know if the water inlet valve or control board is causing the dispenser problem?
How do I find the correct Hotpoint washer dispenser replacement part?