Unlock the Right Part
for Your Repair
Find the exact part you need
Enter your model number to see parts that fit your machine.
Choose Product
Identify Problem
03
Find Solutions
HomeRepair HelpInglis Washer RepairInglis Washer dispenser not working properly Repair
Inglis Washer dispenser not working properly
When your Inglis washer dispenser is not working, detergent, bleach, or fabric softener may remain in the dispenser drawer or fail to reach the tub. The most likely cause is low household water pressure or a faulty water inlet valve. The valve needs at least 20 psi to supply enough water to flush the dispenser, so check the pressure first and replace the valve if pressure is adequate but water flow remains weak. Next, inspect the detergent container for clogs, misalignment, or damage. A blocked or damaged washer dispenser or drawer can also prevent proper dispensing, while a plugged siphon tube may leave diluted detergent or softener in the tray. Clean the compartment, trays, and siphon break before replacing parts. If these components check out, the control board may not be sending power to the dispenser valves or actuator at the correct time. Use a multimeter to test for voltage, following proper safety procedures. Enter your Inglis washer model number to find the exact replacement water inlet valve, detergent container, dispenser, siphon break, drawer, or control board for your specific washing machine.
01 - Inglis Washing Machine Dispenser
A washer detergent dispenser not working is often the result of low water pressure in the home or a defective water inlet valve not supplying water to the dispenser. However, it's also possible the dispenser drawer is obstructed or damaged and not allowing the detergent to be dispensed. You should inspect the drawer for any obstructions or damage and replace the component if necessary.
Enter model number to search for the required part specific to your product
Top Solution
02 - Inglis Washing Machine Water Inlet Valve
The dispenser uses water from the inlet valve to flush out the detergent and fabric softener from the dispenser. If the water flow is too slow the dispenser will not distribute the detergent and softener properly. The water inlet valve requires at least 20 psi to function properly. First, check the water pressure to determine that it is adequate. If the water pressure is adequate, replace the water inlet valve.
Top Solution
03 - Inglis Washing Machine Detergent Container
The dispenser's detergent container could be clogged, misaligned, or damaged, and unable to dispense its contents properly. Inspect the detergent container for any damage and replace if necessary.
Top Solution
04 - Inglis Washing Machine Siphon Break
Some dispensers use a siphon tube. If the siphon tube gets plugged you may get a diluted mixture of detergent, bleach, or fabric softener remaining in the tray. Make sure the dispenser compartment trays and siphon tubes are clean.
Highly Likely
05 - Inglis Washing Machine Drawer
A washer dispenser not working is often the result of low water pressure in the home or a defective water inlet valve not supplying water to the dispenser. However, it's also possible the dispenser drawer is obstructed or damaged and not allowing the detergent, bleach, or fabric softener to be dispensed. You should inspect the drawer for any obstructions or damage and replace the component if necessary.
Common
06 - Inglis Washing Machine Detergent Dispenser
Most washer dispensers use a water inlet valve to move water through the different dispenser compartments at specified times to dispense the soap or fabric softener. Some models use a diverter motor. If the dispenser is clogged and cannot be cleaned or the water inlet valve is part of the dispenser and no water is flowing through it, the dispenser will need to be replaced.
Common
07 - Inglis Washing Machine Control Board
A washer detergent dispenser not working is often the result of low water pressure in the home or a defective water inlet valve not supplying water to the dispenser. However, it's also possible the appliance's control board is not sending power to the dispenser water valves or dispenser actuator at the proper times. You can use a multimeter to help determine if voltage is reaching these components. If not, the control board will need to be replaced.
Common
Frequently Asked Questions
Why is my Inglis washer not dispensing detergent or fabric softener?
Can low water pressure cause my washing machine dispenser not to work?
How do I fix an Inglis washer detergent tray that is not draining?
How can I tell whether the control board is causing my washer dispenser problem?
How do I identify and buy the correct Inglis washer dispenser part?