Unlock the Right Part
for Your Repair
Find the exact part you need
Enter your model number to see parts that fit your machine.
Choose Product
Identify Problem
03
Find Solutions
HomeRepair HelpE-Wave Washer RepairE-Wave Washer dispenser not working properly Repair
E-Wave Washer dispenser not working properly
Is your E-Wave washer dispenser not working? Detergent, bleach, or fabric softener may remain in the drawer or fail to flush into the tub. The most likely cause is low household water pressure or a faulty water inlet valve. The valve needs at least 20 psi to supply enough water to the dispenser, so check the pressure first. If pressure is adequate, replace the water inlet valve. Next, inspect the detergent container for clogs, misalignment, or damage, then check the dispenser and dispenser drawer for obstructions or cracks that could prevent proper dispensing. A plugged siphon break or siphon tube can also leave a diluted mixture in the tray, so clean the dispenser compartments and siphon tubes thoroughly. If water reaches the dispenser but the washer detergent dispenser still does not work, the control board may not be sending power to the water valves or dispenser actuator at the correct time. Use a multimeter to test for voltage before replacing the control board. Enter your E-Wave washer model number to find the exact replacement part for your specific washing machine, including the water inlet valve, detergent container, dispenser, siphon break, drawer, or control board.
01 - E-Wave Washing Machine Dispenser
A washer detergent dispenser not working is often the result of low water pressure in the home or a defective water inlet valve not supplying water to the dispenser. However, it's also possible the dispenser drawer is obstructed or damaged and not allowing the detergent to be dispensed. You should inspect the drawer for any obstructions or damage and replace the component if necessary.
Enter model number to search for the required part specific to your product
Top Solution
02 - E-Wave Washing Machine Water Inlet Valve
The dispenser uses water from the inlet valve to flush out the detergent and fabric softener from the dispenser. If the water flow is too slow the dispenser will not distribute the detergent and softener properly. The water inlet valve requires at least 20 psi to function properly. First, check the water pressure to determine that it is adequate. If the water pressure is adequate, replace the water inlet valve.
Top Solution
03 - E-Wave Washing Machine Detergent Container
The dispenser's detergent container could be clogged, misaligned, or damaged, and unable to dispense its contents properly. Inspect the detergent container for any damage and replace if necessary.
Top Solution
04 - E-Wave Washing Machine Siphon Break
Some dispensers use a siphon tube. If the siphon tube gets plugged you may get a diluted mixture of detergent, bleach, or fabric softener remaining in the tray. Make sure the dispenser compartment trays and siphon tubes are clean.
Highly Likely
05 - E-Wave Washing Machine Drawer
A washer dispenser not working is often the result of low water pressure in the home or a defective water inlet valve not supplying water to the dispenser. However, it's also possible the dispenser drawer is obstructed or damaged and not allowing the detergent, bleach, or fabric softener to be dispensed. You should inspect the drawer for any obstructions or damage and replace the component if necessary.
Common
06 - E-Wave Washing Machine Detergent Dispenser
Most washer dispensers use a water inlet valve to move water through the different dispenser compartments at specified times to dispense the soap or fabric softener. Some models use a diverter motor. If the dispenser is clogged and cannot be cleaned or the water inlet valve is part of the dispenser and no water is flowing through it, the dispenser will need to be replaced.
Common
07 - E-Wave Washing Machine Control Board
A washer detergent dispenser not working is often the result of low water pressure in the home or a defective water inlet valve not supplying water to the dispenser. However, it's also possible the appliance's control board is not sending power to the dispenser water valves or dispenser actuator at the proper times. You can use a multimeter to help determine if voltage is reaching these components. If not, the control board will need to be replaced.
Common
Frequently Asked Questions
Why is my E-Wave washer not dispensing detergent or fabric softener?
How do I fix an E-Wave washer detergent dispenser that is clogged or not draining?
Could a bad water inlet valve cause my washing machine dispenser not to work?
How can I tell if the control board is causing my E-Wave washer dispenser problem?
How do I find the correct E-Wave washer dispenser part?