Unlock the Right Part
for Your Repair
Find the exact part you need
Enter your model number to see parts that fit your machine.
Choose Product
Identify Problem
03
Find Solutions
HomeRepair HelpCrosley Washer RepairCrosley Washer dispenser not working properly Repair
Crosley Washer dispenser not working properly
When your Crosley washer dispenser is not working, the most likely cause is low water pressure or a faulty water inlet valve. The dispenser needs at least 20 psi to flush detergent and fabric softener from the tray, so check household water pressure first. If pressure is adequate, the inlet valve may not be supplying enough water and should be tested or replaced. A clogged, misaligned, or damaged detergent container is another common reason for a washer not dispensing detergent. Inspect the container, dispenser drawer, and dispenser for buildup, obstructions, or damage. If your model uses a siphon break or siphon tube, clean it thoroughly because a blockage can leave diluted detergent, bleach, or fabric softener behind. Less commonly, the control board may not send power to the dispenser valves or actuator at the correct time. A multimeter can help verify voltage before replacing the board. These detergent dispenser problems can usually be repaired with the correct Crosley washing machine water inlet valve, dispenser, drawer, container, siphon break, or control board. Enter your model number to find the exact replacement part for your specific washing machine.
01 - Crosley Washing Machine Dispenser
A washer detergent dispenser not working is often the result of low water pressure in the home or a defective water inlet valve not supplying water to the dispenser. However, it's also possible the dispenser drawer is obstructed or damaged and not allowing the detergent to be dispensed. You should inspect the drawer for any obstructions or damage and replace the component if necessary.
Enter model number to search for the required part specific to your product
Top Solution
02 - Crosley Washing Machine Water Inlet Valve
The dispenser uses water from the inlet valve to flush out the detergent and fabric softener from the dispenser. If the water flow is too slow the dispenser will not distribute the detergent and softener properly. The water inlet valve requires at least 20 psi to function properly. First, check the water pressure to determine that it is adequate. If the water pressure is adequate, replace the water inlet valve.
Top Solution
03 - Crosley Washing Machine Detergent Container
The dispenser's detergent container could be clogged, misaligned, or damaged, and unable to dispense its contents properly. Inspect the detergent container for any damage and replace if necessary.
Top Solution
04 - Crosley Washing Machine Siphon Break
Some dispensers use a siphon tube. If the siphon tube gets plugged you may get a diluted mixture of detergent, bleach, or fabric softener remaining in the tray. Make sure the dispenser compartment trays and siphon tubes are clean.
Highly Likely
05 - Crosley Washing Machine Drawer
A washer dispenser not working is often the result of low water pressure in the home or a defective water inlet valve not supplying water to the dispenser. However, it's also possible the dispenser drawer is obstructed or damaged and not allowing the detergent, bleach, or fabric softener to be dispensed. You should inspect the drawer for any obstructions or damage and replace the component if necessary.
Common
06 - Crosley Washing Machine Detergent Dispenser
Most washer dispensers use a water inlet valve to move water through the different dispenser compartments at specified times to dispense the soap or fabric softener. Some models use a diverter motor. If the dispenser is clogged and cannot be cleaned or the water inlet valve is part of the dispenser and no water is flowing through it, the dispenser will need to be replaced.
Common
07 - Crosley Washing Machine Control Board
A washer detergent dispenser not working is often the result of low water pressure in the home or a defective water inlet valve not supplying water to the dispenser. However, it's also possible the appliance's control board is not sending power to the dispenser water valves or dispenser actuator at the proper times. You can use a multimeter to help determine if voltage is reaching these components. If not, the control board will need to be replaced.
Common
Frequently Asked Questions
Why is my Crosley washer dispenser not dispensing detergent?
Can a water inlet valve cause dispenser problems in my Crosley washing machine?
How do I clean a Crosley washer detergent dispenser that is not working?
Could the control board cause my Crosley washer dispenser not to work?
How do I find the correct Crosley washer dispenser part?