Choose Product
Identify Problem
03
Find Solutions
HomeRepair HelpWhirlpool Washer RepairWhirlpool Washer stops mid cycle Repair

Whirlpool Washer stops mid cycle

If your Whirlpool washer stops mid cycle, start by checking the incoming power. A loose power cord can interrupt operation, so make sure it is firmly plugged into the outlet. If the washer stops during agitation or spin, a worn tub bearing or rear drum with bearing may prevent the basket from turning smoothly. A failed lid switch assembly can also stop the cycle, especially on top load models, because the switch prevents spinning when the lid is open. Next, inspect the control board, which controls voltage to many washer components and may fail because of a shorted circuit or faulty pressure sensor. On front load models, a defective door lock motor and switch assembly can keep the door from latching and cause the washing machine to stop mid cycle. Check for unusual noise, damaged wiring, loose connections, or a door that does not latch properly. Testing the lid switch and door lock switches with a multimeter can help confirm an electrical failure. Whether your washer stops at the wash cycle or stops with water in it, enter your model number to find the exact replacement part for your specific Whirlpool washing machine.

01 - Incoming Power Problem

Make sure that the power cord is not loose. It must be plugged in tightly to ensure consistent electrical power to the washer.
Top Solution

02 - Whirlpool Washing Machine Tub Bearing

The tub bearing is mounted in the middle of the outer tub. The tub bearing helps to keep the inner tub spinning smoothly. Replacing the tub bearing is a very involved repair and will require disassembling most of the washer. If the tub bearing is defective, we recommend replacing both the outer tub and bearing as an assembly if the manufacturer offers the components together.
Enter model number to search for the required part specific to your product
Need help finding your model number?
Shop all Whirlpool Washing Machine Tub Bearing Parts
Top Solution

03 - Whirlpool Washing Machine Lid Switch Assembly

The lid switch assembly prevents the washer from spinning when the lid is open. If the lid switch assembly fails, the washer may stop mid-cycle. To determine if the lid switch assembly is defective, use a multimeter to test each of the lid switches for continuity. If a lid switch does not have continuity, replace it.
Shop all Whirlpool Washing Machine Lid Switch Assembly Parts
Top Solution

04 - Whirlpool Washing Machine Control Board

Since a washing machine control board provides voltage to nearly all of the washer's electrical components, a board with a shorted component may send continuous voltage to the water inlet valve, causing the washer to overflow. You can inspect the board for signs of burning or a shorted-out component and use a multimeter to test the power output terminals on the board after reviewing the appliance's wiring diagram. Some washing machine control boards will have a built-in pressure sensor used to determine how much water to allow into the tub. The control board pressure sensor monitors the amount of water entering the tub dur...ing the fill cycle and will shut off voltage to the water inlet valve when the water has reached the proper level. A defective control board pressure sensor may allow too much water to fill the tub resulting in the washer overflowing. You can use a multimeter to test for appropriate changes in electrical continuity to help determine if the component is defective.
Shop all Whirlpool Washing Machine Control Board Parts
Top Solution

05 - Whirlpool Washing Machine Rear Drum with Bearing

The rear drum has a bearing or bearings in it to keep the inner tub spinning smoothly. If the tub bearing system is defective the washer can become very noisy. On some machines bearings are sold separately from the rear drum, however we recommend replacing both the outer drum and bearing as an assembly if the manufacturer offers the components together because removing and pressing in the new bearing can be exceptionally difficult. Be aware that replacing the outer tub and bearing is also not easy and can be very costly.
Shop all Whirlpool Washing Machine Rear Drum with Bearing Parts
Top Solution

06 - Whirlpool Washing Machine Door Lock Motor and Switch Assembly

The door lock secures the washer door shut during operation. Once the washer door is closed, the washer can begin operating. If the washer door is not latched shut, the door switch prevents the washer from operating. If the door lock is defective, the washer may stop mid cycle. The door lock can fail either mechanically or electrically. Inspect the door lock for damage. If the door lock is damaged or does not latch properly, replace it. To determine if the door lock has failed electrically, consult your washer’s diagram and use a multimeter to test each of the door lock switches for continuity. If one of the switches does ...not have continuity, replace the switch.
Shop all Whirlpool Washing Machine Door Lock Motor and Switch Assembly Parts
Top Solution

07 - Insufficient water supply

A clogged water inlet valve, the main water supply valve being partially closed, or low water pressure in the home can restrict the amount of water entering the tub, resulting in the washer stopping ahead of the spin cycle. Confirm water pressure is strong at the kitchen faucet and that the home's main water supply valve is fully open.
Top Solution

Frequently Asked Questions

Why does my Whirlpool washer stop mid cycle?
Why does my Whirlpool washer stop mid cycle with water in it?
Can a bad tub bearing make a Whirlpool washer stop mid cycle?
Should I replace the Whirlpool washer control board if it stops mid cycle?
How do I find the correct Whirlpool washer part for a mid-cycle stopping problem?