Unlock the Right Part
for Your Repair
Find the exact part you need
Enter your model number to see parts that fit your machine.
Choose Product
Identify Problem
03
Find Solutions
HomeRepair HelpMontgomery Wards Washer RepairMontgomery Wards Washer stops mid cycle Repair
Montgomery Wards Washer stops mid cycle
When your Montgomery Wards washer stops mid cycle, start with the simplest cause: check that the power cord is firmly plugged into the outlet and the washer is receiving consistent power. A worn tub bearing is another likely problem, especially if the washing machine stops mid cycle after making grinding or other unusual noises. The lid switch assembly can also interrupt operation because it prevents the washer from spinning when the lid is open. Test the lid switches for continuity with a multimeter and replace the assembly if a switch fails. A defective control board may stop sending the correct voltage to the washer's components or may misread the pressure sensor, causing the washer to overfill and stop. The rear drum with bearing can produce excessive noise and may require replacement as an assembly. On models with a door lock, inspect the door lock motor and switch assembly for mechanical damage or failed electrical contacts. Before ordering, enter your model number to find the exact replacement part for your specific Montgomery Wards washing machine.
01 - Incoming Power Problem
Make sure that the power cord is not loose. It must be plugged in tightly to ensure consistent electrical power to the washer.
Top Solution
02 - Montgomery Wards Washing Machine Tub Bearing
The tub bearing is mounted in the middle of the outer tub. The tub bearing helps to keep the inner tub spinning smoothly. Replacing the tub bearing is a very involved repair and will require disassembling most of the washer. If the tub bearing is defective, we recommend replacing both the outer tub and bearing as an assembly if the manufacturer offers the components together.
Enter model number to search for the required part specific to your product
Top Solution
03 - Montgomery Wards Washing Machine Lid Switch Assembly
The lid switch assembly prevents the washer from spinning when the lid is open. If the lid switch assembly fails, the washer may stop mid-cycle. To determine if the lid switch assembly is defective, use a multimeter to test each of the lid switches for continuity. If a lid switch does not have continuity, replace it.
Top Solution
04 - Montgomery Wards Washing Machine Control Board
Since a washing machine control board provides voltage to nearly all of the washer's electrical components, a board with a shorted component may send continuous voltage to the water inlet valve, causing the washer to overflow. You can inspect the board for signs of burning or a shorted-out component and use a multimeter to test the power output terminals on the board after reviewing the appliance's wiring diagram. Some washing machine control boards will have a built-in pressure sensor used to determine how much water to allow into the tub. The control board pressure sensor monitors the amount of water entering the tub dur...
Top Solution
05 - Montgomery Wards Washing Machine Rear Drum with Bearing
The rear drum has a bearing or bearings in it to keep the inner tub spinning smoothly. If the tub bearing system is defective the washer can become very noisy. On some machines bearings are sold separately from the rear drum, however we recommend replacing both the outer drum and bearing as an assembly if the manufacturer offers the components together because removing and pressing in the new bearing can be exceptionally difficult. Be aware that replacing the outer tub and bearing is also not easy and can be very costly.
Top Solution
06 - Montgomery Wards Washing Machine Door Lock Motor and Switch Assembly
The door lock secures the washer door shut during operation. Once the washer door is closed, the washer can begin operating. If the washer door is not latched shut, the door switch prevents the washer from operating. If the door lock is defective, the washer may stop mid cycle. The door lock can fail either mechanically or electrically. Inspect the door lock for damage. If the door lock is damaged or does not latch properly, replace it. To determine if the door lock has failed electrically, consult your washer’s diagram and use a multimeter to test each of the door lock switches for continuity. If one of the switches does ...
Top Solution
07 - Insufficient water supply
A clogged water inlet valve, the main water supply valve being partially closed, or low water pressure in the home can restrict the amount of water entering the tub, resulting in the washer stopping ahead of the spin cycle. Confirm water pressure is strong at the kitchen faucet and that the home's main water supply valve is fully open.
Top Solution
Frequently Asked Questions
Why does my Montgomery Wards washer stop mid cycle?
What should I check if my washer stops at the wash cycle or will not continue?
Can a noisy washing machine stop mid cycle because of a bad tub bearing?
How do I know whether the control board is causing my washer to stop mid cycle?
How do I find the correct Montgomery Wards washer replacement part?