Unlock the Right Part
for Your Repair
Find the exact part you need
Enter your model number to see parts that fit your machine.
Order by 2:00 a.m., and we'll ship the same day
Price Match Guarantee
Order by 2:00 a.m., and we'll ship the same dayChoose Product
Identify Problem
03
Find Solutions
HomeRepair HelpInglis Washer RepairInglis Washer not filling properly Repair
Inglis Washer not filling properly
If your Inglis washer is not filling, or your washing machine is not filling with water, start with the lid switch assembly. If the water inlet valve has power and tests normally but the tub does not spin during the spin cycle, a defective lid switch may prevent the washer from filling. Test the lid switch for continuity with a multimeter and replace it if it fails. Next, check for a water inlet valve problem. Confirm the household water pressure is adequate, clean debris from the valve’s inlet screens, and replace the valve if the washer fills slowly or does not fill. A faulty control board may also fail to send voltage to the inlet valve. Inspect it for burned components and test for voltage during the fill cycle. Low household water pressure can cause the same symptoms, so check water flow at a nearby faucet. If only hot or cold water enters, test the temperature switch for continuity. Finally, make sure both hot and cold water supply valves are fully open. Enter your Inglis washer model number to find the exact replacement part for your specific washing machine.
01 - Inglis Washing Machine Lid Switch Assembly
If you've confirmed the water inlet valve is receiving power and is functioning normally, you should determine if the washer tub is spinning during the spin cycle. If not, the lid switch assembly could be defective and responsible for the tub not filling as expected. To determine if the lid switch assembly is defective, use a multimeter to test the lid switch for continuity. If the lid switch does not have continuity, replace it.
Enter model number to search for the required part specific to your product
Top Solution
02 - Inglis Washing Machine Water Inlet Valve
The water inlet valve opens to allow water to enter the washing machine. If the water inlet valve is defective, the wash may fill slowly or not fill at all. The water inlet valve requires sufficient water pressure to function properly. First, check the water pressure to determine that it is adequate. If the water pressure is adequate, try cleaning the screens inside the water inlet valve hose connection ports. If the washer still fills slowly, replace the water inlet valve.
Top Solution
03 - Inglis Washing Machine Control Board
Since a washing machine control board provides voltage to nearly all of the washer's electrical components, a faulty board may not be sending power to the inlet valve to open it and allow water to fill the tub. You can inspect the board for signs of burning or a shorted-out component. You can also use a multimeter to test for incoming power to the inlet valve after reviewing the appliance's wiring diagram. If no voltage is present when the washer is in the fill cycle, it's likely the control board is defective and will need to be replaced.
Top Solution
04 - Low Water Pressure from House Supply
The home water pressure might be too low. The water inlet valve requires good water pressure to function properly. You can check the water flow at the kitchen faucet to help determine if the home's water pressure is sufficient or not.
Top Solution
05 - Inglis Washing Machine Temperature Switch
The temperature selector switch allows power to be sent to the water inlet valve to release hot or cold water. If the temperature selector switch is faulty, the valve may only allow only one temperature of water to fill the tub. You can use a multimeter to test the switch for electrical continuity. If the switch tests negative for continuity, the part will need to be replaced.
Highly Likely
06 - Water Supply Valves are Closed
Confirm that both the hot and cold water supply valves are open. If the valves are closed the washer won't fill to start the wash cycle.
Highly Likely
07 - Water siphoning from tub
If the water is siphoning from the tub the outlet end of the drain hose is likely lower than the water level in the tub. The drain hose should terminate between 30 inches to 36 inches (77 centimeters to 92 centimeters) above the floor, depending on the model, in a standpipe or laundry tub. If the drain hose is sealed at the top of the standpipe or excess hose is pushed too far down into the pipe, siphoning can also occur.
Highly Likely
Frequently Asked Questions
Why is my Inglis washer not filling with water?
What should I check if my washer fills slowly?
Can a lid switch cause an Inglis washer not to fill?
How do I know whether the water inlet valve or control board is bad?
How can I find the correct Inglis washer water inlet valve or lid switch?