Unlock the Right Part
for Your Repair
Find the exact part you need
Enter your model number to see parts that fit your machine.
Choose Product
Identify Problem
03
Find Solutions
HomeRepair HelpEstate Washer RepairEstate Washer not filling properly Repair
Estate Washer not filling properly
If your Estate washer is not filling, or your washing machine is not filling with water, start by checking whether the tub spins during the spin cycle after confirming the water inlet valve has power. A defective lid switch assembly can prevent the washer from filling as expected, so test the lid switch for continuity and replace it if it fails. Next, check for a water inlet valve problem. Low household water pressure or clogged screens in the valve hose ports can make the washer fill slowly or not fill at all. If pressure and screens are good, the water inlet valve may need replacement. A faulty control board can also prevent voltage from reaching the valve, while a defective temperature switch may allow only hot or cold water to enter. Confirm both household water supply valves are fully open. These checks cover common causes of a washer not filling, including a washer with no water and a washer that fills slowly. Enter your Estate washer model number to find the exact replacement lid switch assembly, water inlet valve, control board, or temperature switch for your specific machine.
01 - Estate Washing Machine Lid Switch Assembly
If you've confirmed the water inlet valve is receiving power and is functioning normally, you should determine if the washer tub is spinning during the spin cycle. If not, the lid switch assembly could be defective and responsible for the tub not filling as expected. To determine if the lid switch assembly is defective, use a multimeter to test the lid switch for continuity. If the lid switch does not have continuity, replace it.
Enter model number to search for the required part specific to your product
Top Solution
02 - Estate Washing Machine Water Inlet Valve
The water inlet valve opens to allow water to enter the washing machine. If the water inlet valve is defective, the wash may fill slowly or not fill at all. The water inlet valve requires sufficient water pressure to function properly. First, check the water pressure to determine that it is adequate. If the water pressure is adequate, try cleaning the screens inside the water inlet valve hose connection ports. If the washer still fills slowly, replace the water inlet valve.
Top Solution
03 - Estate Washing Machine Control Board
Since a washing machine control board provides voltage to nearly all of the washer's electrical components, a faulty board may not be sending power to the inlet valve to open it and allow water to fill the tub. You can inspect the board for signs of burning or a shorted-out component. You can also use a multimeter to test for incoming power to the inlet valve after reviewing the appliance's wiring diagram. If no voltage is present when the washer is in the fill cycle, it's likely the control board is defective and will need to be replaced.
Top Solution
04 - Low Water Pressure from House Supply
The home water pressure might be too low. The water inlet valve requires good water pressure to function properly. You can check the water flow at the kitchen faucet to help determine if the home's water pressure is sufficient or not.
Top Solution
05 - Estate Washing Machine Temperature Switch
The temperature selector switch allows power to be sent to the water inlet valve to release hot or cold water. If the temperature selector switch is faulty, the valve may only allow only one temperature of water to fill the tub. You can use a multimeter to test the switch for electrical continuity. If the switch tests negative for continuity, the part will need to be replaced.
Highly Likely
06 - Water Supply Valves are Closed
Confirm that both the hot and cold water supply valves are open. If the valves are closed the washer won't fill to start the wash cycle.
Highly Likely
07 - Water siphoning from tub
If the water is siphoning from the tub the outlet end of the drain hose is likely lower than the water level in the tub. The drain hose should terminate between 30 inches to 36 inches (77 centimeters to 92 centimeters) above the floor, depending on the model, in a standpipe or laundry tub. If the drain hose is sealed at the top of the standpipe or excess hose is pushed too far down into the pipe, siphoning can also occur.
Highly Likely
Frequently Asked Questions
Why is my Estate washer not filling with water?
Why is my Estate washer filling slowly or with only hot or cold water?
My Estate washer has water pressure, but it still will not fill. What should I check?
Could the Estate washer control board be causing the washer not to fill?
How do I find the correct Estate washer water inlet valve or lid switch?