Choose Product
Identify Problem
03
Find Solutions
Washer is making loud noise
Brand:Roper
Model:RAP5244AL0
Product:Washing Machine
Featured Video
Top 5 Reasons Front-Load Washer Is Making Loud Noise?
02:19
Common solutions for: Washer is making loud noise
01 - Shipping bolts have not been removed
Shipping bolts and a foam block are often used when transporting new washing machines to prevent the tub from moving and becoming damaged. Confirm the bolts (located at the rear of the washer) and the foam block have been removed before operating the appliance.
Top Solution
02 - Improperly balanced load
If there are light and heavy items in the same load, or too few items, the tub can spin out of balance. Wash items with aproximately the same weight together, and consider adding items if necessary, to better balance the load.
Highly Likely
03 - Washer not level
The washer should be level with the feet sitting firmly on a solid floor. Level the appliance and adjust the legs if necessary.
Highly Likely
04 - Pulley
The drive pulley might be worn out, cracked, loose or bent. Remove the drive pulley and inspect it carefully. If the drive pulley is damaged or defective, replace it.
Genuine Part
Common
05 - Suspension Rod
A top-load washer tub is usually supported by four suspension rods. If one of the suspension rods becomes dislodged or breaks, the tub may begin shaking and hitting the sides of the washer cabinet, making a loud noise during operation. Suspension rods will often come in a set of four and it is recommended to replace all four of the rods at the same time to reduce uneven wear.
Genuine Part
Genuine Part
Common
06 - Foreign objects in the tub or pump
Foreign objects such as coins or safety pins may be in the tub or pump. Inspect the tub for foreign objects that may be rattling around. Most front-load washers have a removable drain trap behind a small door near the bottom of the washer to keep items from getting to the pump. Unplug the power cord for safety, then inspect the drain trap and remove any items as needed.
Common
07 - Drive Belt
The drive belt might be defective. Over time, the drive belt can dry or burn out and starts to crack. Eventually, a piece of the belt can break off, causing the belt to make a loud noise whenever the motor is running. To determine if the drive belt is broken, inspect the drive belt. If the drive belt is broken or damaged, replace it.
Less Common
08 - Control Board
A continuous beeping sound could be the result of a faulty control board. However, you should check any fault codes that may be displayed on the control panel to determine if the washer has an operation problem before considering a control board replacement.
Genuine Part
Less Common
09 - Transmission
The washer transmission might be worn out or defective. Transmissions have gears in them that can fail causing the washer to to be noisy during operation. However, this is almost never the case. Before replacing the transmission, first check all of the other more commonly defective parts.
Less Common
10 - Drain Pump
If the washer is making a loud noise while draining, the drain pump might be clogged or defective. Sometimes, small objects or articles of clothing can get caught in the drain pump. To determine if anything is blocking the drain pump, remove the drain pump and check the pump for obstructions. If the drain pump is clear of obstructions, but is still noisy during the drain cycle, replace the drain pump.
Uncommon But Possible
11 - Drive Motor
The drive motor bearings might be worn out. Washer motors are normally very quiet during operation. To determine if the washer motor is defective, remove the drive belt from the washer and then run the motor. If the motor is still loud, this indicates that the drive motor is defective and needs to be replaced.
Uncommon But Possible
12 - Hub
The hub is seated on top of the transmission and engages with the inner tub. If the transmission is engaged to spin, and the outer tub is making a loud noise, the hub may be worn. Inspect the hub for damage or wear and replace if necessary.
Uncommon But Possible
13 - Water Inlet Valve
If the washer is noisy or loud, particularly when the washer is filling, the water inlet valve may be at fault. Over time, mineral deposits can build up inside the valve and cause a restriction. If the water inlet valve is restricted, it will make noise during the fill cycle. If the water inlet valve is defective, replace it. Do not attempt to repair the water inlet valve—taking apart the valve makes it susceptible to failure.
Uncommon But Possible