When your Ikea microwave is not working, not turning on, or has power but is not working, start with the line fuse. A blown line fuse stops the microwave from starting; test it for continuity and correct the underlying electrical problem before installing a replacement, or the new fuse may blow too. Next, inspect the switch holder behind the control panel. If it is damaged or misaligned, the door switches may not actuate when the door closes, leaving the microwave stopped. A defective main control board can also cause a microwave to stop working, but it is rarely the problem, so test the more common parts first. If the microwave overheated, the thermostat may have opened and stopped voltage from reaching the high-voltage components. Also verify that the wall outlet has power, then test the non-resettable thermal fuse for continuity. Enter your Ikea microwave model number to find the exact replacement line fuse, switch holder, thermostat, thermal fuse, or control board for your appliance. Any repair that requires opening the outer cabinet must be handled carefully because the high-voltage capacitor can store a lethal charge even after the microwave is unplugged. Proper capacitor discharge is required before interior work, and a qualified technician should perform the repair if you are not familiar with that procedure.
01 - Ikea Microwave Line Fuse
If too much current passes through the microwave circuitry, the line fuse will blow. If the line fuse blows, the microwave won’t start. To determine if the line fuse is at fault, use a multimeter to test it for continuity. If the fuse does not have continuity, replace it. In addition, you should investigate and resolve the problem that caused the fuse to blow. If you don’t resolve the underlying issue, the new fuse will blow too. (Caution: The microwave oven can store thousands of volts of electricity in its high voltage capacitor, even after the microwave oven has been unplugged. Due to the potential for electric shock, i...t is extremely dangerous to replace the electronic components in a microwave. Only a licensed technician should replace the line fuse.)
Enter model number to search for the required part specific to your product
The microwave switch holder is the component that houses the door switches behind the control panel. If the switch holder is damaged or misaligned, one of more switches may not be actuated when the microwave door is closed, resulting in the microwave not working. You will need to uninstall the control panel and inspect the switch holder to confirm it is in good condition and secured properly. Replace the switch holder with a new one if necessary.
The main control board might be defective. However, this is rarely the case. Control boards are often misdiagnosed—check all of the more commonly defective parts. If you have determined that all of the other components are working properly,replace the main control board. (Caution: The microwave oven can store thousands of volts of electricity in its high voltage capacitor, even after the microwave oven has been unplugged. Due to the potential for electric shock, it is extremely dangerous to replace the electronic components in a microwave. Only a licensed technician should replace the main control board.)
If the microwave overheats, the thermostat trips to cut off voltage to the microwave. If the thermostat is shorted open, it may not allow voltage to reach the high voltage components. To determine if the thermostat is at fault, use a multimeter to test it for electrical continuity. If the thermostat does not have continuity, and it cannot be reset, replace it.
The electrical outlet may not be getting power. To determine if the outlet is getting power, try plugging something else into the outlet. If the outlet is not getting power, check the home circuit breakers or fuses.
Highly Likely
06 - Ikea Microwave Diode
The diode converts the A/C power output of the transformer to D/C, doubling the voltage to nearly 5,000 volts. This high voltage powers the magnetron to heat the food. If the diode burns out, the magnetron won’t receive enough voltage to operate, preventing the microwave from working. When the diode fails, it is often visibly burned out. Inspect the diode and if the diode is burned out, replace it. If inspecting the diode proves inconclusive, test it with a multimeter that uses a 9-volt battery or put a 9-volt battery in series with the diode. When the leads are reversed, the diode should only have continuity in one direct...ion. (Warning: The microwave oven can store a lethal amount of electricity in its high voltage capacitor, even after the microwave oven has been unplugged. Due to the high running voltage and the potential for electric shock, it is extremely dangerous to replace the electronic components in a microwave. Only a licensed technician should replace the diode.)
The thermal fuse cuts off power to the microwave if the microwave overheats. To determine if the thermal fuse has blown, use a multimeter to test it for continuity. If the fuse does not have continuity, replace it. The thermal fuse cannot be reset—if the fuse is blown, it must be replaced. (Caution: The microwave oven can store thousands of volts of electricity in its high voltage capacitor, even after the microwave oven has been unplugged. Due to the potential for electric shock, it is extremely dangerous to replace the electronic components in a microwave. Only a licensed technician should replace the thermal fuse.)