Choose Product
Identify Problem
03
Find Solutions
HomeRepair HelpMaytag Microwave RepairMaytag Microwave not heating Repair

Maytag Microwave not heating

If your Maytag microwave is not heating, the oven may run normally while the food stays cold, which usually points to a failed heating component or door safety circuit. The most likely cause is a defective high-voltage diode, which prevents the magnetron from receiving the voltage needed to produce heat. Next, check the door switch, including the primary, secondary, or monitor switch, because a failed switch can keep the microwave from starting the heating cycle. A burned-out magnetron can also cause a microwave not heating food, followed by an open thermostat or thermal fuse that has stopped voltage from reaching the high-voltage circuit. Less commonly, the high-voltage capacitor or high-voltage transformer may have failed. If the transformer is arcing or the microwave smells burnt, stop using it. Testing or replacing the diode, magnetron, high-voltage capacitor, or high-voltage transformer, or opening the outer cabinet for any interior repair, is hazardous because the capacitor can store a lethal charge even after the microwave is unplugged. It must be properly discharged first, so use a qualified technician if you are not familiar with capacitor discharge procedures. Enter your model number to find the exact replacement part for your Maytag microwave.

01 - Maytag Microwave Diode

The diode converts the A/C power output of the transformer to D/C, doubling the voltage to nearly 5,000 volts. This high voltage powers the magnetron to heat the food. If the diode burns out, the magnetron won’t receive enough voltage to operate, preventing the microwave from heating. When the diode fails, it is often visibly burned out. Inspect the diode and if the diode is burned out, replace it. If inspecting the diode proves inconclusive, test it with a multimeter that uses a 9-volt battery or put a 9-volt battery in series with the diode. When the leads are reversed, the diode should only have continuity in one direct...ion. (Warning: The microwave oven can store a lethal amount of electricity in its high voltage capacitor, even after the microwave oven has been unplugged. Due to the high running voltage and the potential for electric shock, it is extremely dangerous to replace the electronic components in a microwave. Only a licensed technician should replace the diode.)
Enter model number to search for the required part specific to your product
Need help finding your model number?
Shop all Maytag Microwave Diode Parts
Top Solution

02 - Maytag Microwave Door Switch

Most microwaves have three or four door switches. When the microwave door closes, the door switches actuate in sequence to ensure that the door is closed properly. If any of the door switches fails, the microwave will not start or heat. To determine if any of the door switches are defective, use a multimeter to test each of the switches for continuity. If any of the door switches does not have continuity, replace it. (Caution: The microwave oven can store thousands of volts of electricity in its high voltage capacitor, even after the microwave oven has been unplugged. Due to the potential for electric shock, it is extremel...y dangerous to replace the electronic components in a microwave. Only a licensed technician should replace a door switch.)
Shop all Maytag Microwave Door Switch Parts
Top Solution

03 - Maytag Microwave Magnetron

The magnetron uses high voltage, high current DC power to generate the microwave frequency that cooks the food. If the magnetron burns out, the microwave won’t heat. The magnetron is not repairable—if the magnetron is burned out, you must replace it. (Warning: The microwave oven can store a lethal amount of electricity in its high voltage capacitor, even after the microwave oven has been unplugged. Due to the high running voltage and the potential for electric shock, it is extremely dangerous to replace the electronic components in a microwave. Only a licensed technician should replace the magnetron.)
Shop all Maytag Microwave Magnetron Parts
Highly Likely

04 - Maytag Microwave Thermostat

If the microwave overheats, the thermostat trips to cut off voltage to the microwave. If the thermostat is shorted open, it may not allow voltage to reach the high voltage components. To determine if the thermostat is at fault, use a multimeter to test it for electrical continuity. If the thermostat does not have continuity, and it cannot be reset, replace it.
Shop all Maytag Microwave Thermostat Parts
Highly Likely

05 - Maytag Microwave High Voltage Capacitor

The high voltage capacitor works with the high voltage diode to convert the output of the transformer to DC voltage and to double the output voltage. If the capacitor is burned out, the entire high voltage circuit will stop working properly, and the microwave won’t heat. To determine if the high voltage capacitor is defective, use a VOM meter with a capacitance testing capability. (“Warning: The microwave oven can store a lethal amount of electricity in its high voltage capacitor, even after the microwave oven has been unplugged. Due to the high running voltage and the potential for electric shock, it is extremely dangerou...s to replace the electronic components in a microwave. Only a licensed technician should replace the high voltage capacitor.)
Shop all Maytag Microwave High Voltage Capacitor Parts
Common

06 - Maytag Microwave High Voltage Transformer

Microwave ovens produce a very high voltage in order to power the magnetron antenna, which emits the energy that cooks the food. When a high voltage transformer fails, it will usually arc and have a burning smell. (Warning: The microwave oven can store a lethal amount of electricity in its high voltage capacitor, even after the microwave oven has been unplugged. Due to the high running voltage and the potential for electric shock, it is extremely dangerous to replace the electronic components in a microwave. Only a licensed technician should replace the high voltage transformer.)
Shop all Maytag Microwave High Voltage Transformer Parts
Common

07 - Maytag Microwave Thermal Fuse

The thermal fuse cuts off power to the microwave if the microwave overheats. To determine if the thermal fuse has blown, use a multimeter to test it for continuity. If the fuse doesn’t have continuity, replace it. The thermal fuse cannot be reset—if the fuse is blown, it must be replaced. (Caution: The microwave oven can store thousands of volts of electricity in its high voltage capacitor, even after the microwave oven has been unplugged. Due to the potential for electric shock, it is extremely dangerous to replace the electronic components in a microwave. Only a licensed technician should replace the thermal fuse.)
Shop all Maytag Microwave Thermal Fuse Parts
Less Common

Frequently Asked Questions

Why is my Maytag microwave not heating even though it runs?
How do I test a Maytag microwave door switch or thermal fuse?
Is the magnetron the reason my microwave stopped heating?
What should I do if my Maytag microwave is sparking or smells like burning?
How do I find the correct Maytag microwave replacement part?