Choose Product
Identify Problem
03
Find Solutions
HomeRepair HelpARDO Dryer RepairARDO Dryer won't stop Repair

ARDO Dryer won't stop

If your ARDO dryer won't stop or keeps running after the cycle finishes, the most likely cause is restricted airflow from a clogged vent or lint buildup, which raises cabinet temperature and forces the machine to keep tumbling to try to dry the load. Next, check whether the anti-wrinkle or similar timed-tumble option is engaged, since that setting will intermittently tumble clothes after a cycle. A clogged or worn blower wheel can also make drying inefficient and keep the drum running longer, especially if lint or small items jam the wheel or the wheel sleeve lets it wobble. Less commonly, intermittent incoming power from a loose plug or tripped breaker will cause odd stopping and starting, and a faulty control board can allow the dryer to run past the end of a cycle. If you need parts—blowers, controls, or venting components—enter your dryer model number at RepairClinic.com to find the exact replacement part for your machine and get step-by-step repair guidance.

01 - Air Flow Problem

If the vent line is clogged or partially clogged, it will restrict the airflow through the dryer, substantially increasing the drying time and cabinet temperature and potentially causing a burning smell. To ensure proper dryer performance, you should clean your dryer's venting system at least once per year.
Top Solution

02 - Anti-wrinkle cycle option selected

Most dryer models have an anti-wrinkle cycle option that can be selected to reduce wrinkles. When selected the dryer drum will tumble the clothes every few minutes after the cycle is completed to help keep wrinkles from occurring. If this option was inadvertently selected the dryer will intermittently run until the clothes are removed.
Top Solution

03 - ARDO Dryer Blower Wheel

The blower wheel draws air through the dryer and pushes the air out the vent. Clumps of lint, socks, and small articles of clothing can escape the lint filter and get caught in the blower wheel. In addition, the blower wheel sleeve can wear out, allowing the blower wheel to wobble on the motor shaft. If the blower wheel is obstructed or defective, it may take too long to dry clothes. To determine if the blower wheel is working properly, remove the dryer vent and assess the strength of the air flow. If the air flow is weak, check the blower wheel for obstructions. If no obstructions are present, try rotating the blower whee...l by hand. If the blower wheel wobbles as it turns, replace it.
Enter model number to search for the required part specific to your product
Need help finding your model number?
Shop all ARDO Dryer Blower Wheel Parts
Top Solution

04 - Incoming Power Problem

Confirm a circuit breaker has not tripped and the power cord is plugged tightly into the wall receptacle. A loose plug can provide intermittent power to the dryer and cause it to spinning stop during the cycle.
Top Solution

05 - ARDO Dryer Control Board

A dryer's control board controls the voltage being sent to all of the appliance's electrical components. If there's no obstruction in the dryer's venting and the dryer is heating to the proper temperature, it's possible the control board is defective and allowing the appliance to run longer than it should. You can inspect the board for signs of damage or a shorted component. You can also use a multimeter to test for voltage reaching the drive motor after reviewing the dryer's wiring diagram.
Shop all ARDO Dryer Control Board Parts
Common

06 - ARDO Dryer Main Control Board

A dryer's main control board controls the voltage being sent to all of the appliance's electrical components. If there's no obstruction in the dryer's venting and the dryer is heating to the proper temperature, it's possible the control board is defective and allowing the appliance to run longer than it should. You can inspect the board for signs of damage or a shorted component.
Shop all ARDO Dryer Main Control Board Parts
Common

07 - Dirty Moisture Sensor Bars

The control board uses the moisture sensor bars to sense the dampness of the clothes. Over time the sensor bars can become coated, expecially from dryer sheet residue. Try cleaning off the bars with warm soap and water. If the sensor bars are damaged they will need to be replaced.
Common

Frequently Asked Questions

Why won't my dryer stop running after the cycle?
Can a clogged vent make my dryer overheat or keep running?
My dryer starts then stops after a few seconds. Could this be a power problem?
How can I tell if the blower wheel is bad and needs replacement?
How do I enter my model number or part number on RepairClinic to find the right replacement part?