Choose Product
Identify Problem
03
Find Solutions
HomeRepair HelpMaytag Dryer RepairMaytag Dryer overheating Repair

Maytag Dryer overheating

If your Maytag dryer is overheating, running too hot, or overheating and shuts off, the most likely cause is the heating element or heating element assembly— a partially shorted element can keep producing heat even after the dryer reaches temperature. Use a multimeter to check continuity and test each terminal to the case; continuity to the case means the element is shorted and should be replaced. A faulty timer that allows continuous voltage to the heating circuit is possible but rare, so test the timer with a multimeter and the wiring diagram only after checking the more common parts. Restricted airflow from a clogged vent or lint buildup will raise cabinet temperature and drying times, so inspect and clean the lint screen, ductwork and outside vent hood. A drive motor that overheats can make the dryer run until it cools and then stop, and a bad thermistor can send incorrect temperature readings to the control board; test the thermistor for continuity and watch for its resistance to fall as it warms. Enter your model number on RepairClinic.com to find the exact replacement part for your dryer.

01 - Maytag Dryer Heating Element

The heating element warms the air before the air enters the dryer drum. If the element is partially shorted out, it may produce heat continuously, even if the dryer has reached the proper temperature. When this happens, the dryer gets too hot. To determine if the heating element is at fault, use a multimeter to test each terminal for continuity to the case. If the heating element has continuity to the case, it is shorted out. If the heating element is shorted out, replace it.
Enter model number to search for the required part specific to your product
Need help finding your model number?
Shop all Maytag Dryer Heating Element Parts
Top Solution

02 - Maytag Dryer Heating Element Assembly

The heating element warms air as it passes over the element. If the element is partially shorted out, it may produce heat continuously, even if the dryer has reached the proper temperature. When this happens, the dryer gets too hot. To determine if the heating element is at fault, first use a multimeter to test the heating element for continuity. If the heating element does not have continuity, replace it. Next, test for continuity from each terminal to the case. If the heating element has continuity to the case, it is shorted out. If the heating element is shorted out, replace it.
Shop all Maytag Dryer Heating Element Assembly Parts
Top Solution

03 - Maytag Dryer Timer

A dryer that is overheating could be caused by a faulty timer allowing continuous voltage to be sent to the heating circuit. If the timer's heating contacts and the heating element are shorted, the heating element can heat when the timer is off. However, this is very rarely the case. Before replacing the timer, check all the more commonly defective parts. If you determine that all of the other components are working properly, test the timer by using a multimeter and consulting the wiring diagram. If the timer is defective, replace it.
Shop all Maytag Dryer Timer Parts
Top Solution

04 - Air Flow Problem

If the vent line is clogged or partially clogged, it will restrict the airflow through the dryer, substantially increasing the drying time and cabinet temperature and potentially causing a burning smell. To ensure proper dryer performance, you should clean your dryer's venting system at least once per year.
Top Solution

05 - Maytag Dryer Drive Motor

A dryer's drive motor will drive the drum belt to rotate the drum as well as spin a blower wheel to circulate the air through the drum during operation. If the dryer runs for a while and then stops, and won't start again until it cools down, it's likely the drive motor is malfunctioning and will need to be replaced.
Shop all Maytag Dryer Drive Motor Parts
Highly Likely

06 - Maytag Dryer Thermistor

A dryer thermistor monitors the dryer temperature and sends a resistance reading to the control board. If the thermistor is malfunctioning, it may fail to send the correct reading to the control board resulting in the dryer overheating. If you've determined there is good air flow coming out the home's outside vent hood and the dryer venting is free of obstructions, the thermistor is one of the components you can test for electrical continuity with a multimeter to see if it's functioning properly. While the thermistor should have continuity at room temperature, the ohm’s reading should go lower as the temperature on the sen...sor increases. If the thermistor has shorted or shows no continuity it should be replaced with a new one. Thermistors rarely get out of calibration.
Shop all Maytag Dryer Thermistor Parts
Highly Likely

07 - Maytag Dryer Main Control Board

A dryer's main control board controls the voltage being sent to all of the appliance's electrical components. If a relay on the board has shorted, it may sent continuous voltage to the heating circuit causing the dryer to overheat. To help determine this, you can inspect the board for signs of damage or a shorted component.
Shop all Maytag Dryer Main Control Board Parts
Common

Frequently Asked Questions

Why is my dryer overheating?
My dryer starts then stops and won't start again until it cools down. What could be wrong?
How do I test the heating element if the dryer is running too hot?
Can clogged vents make my dryer overheat and smell like burning?
How do I enter my model number or part number on RepairClinic.com to find the right replacement part?