Choose Product
Identify Problem
03
Find Solutions
HomeRepair HelpMaytag Dryer RepairMaytag Dryer steam function not working Repair

Maytag Dryer steam function not working

If your Maytag dryer’s steam function is not working, start by treating the control board as the most likely culprit: if the board is not sending power to the steam generator or the water inlet valve, the steam cycle will fail, and a visual inspection for burned or shorted components can help you decide if the board needs replacing. Next likely is a failed steam generator, especially when the generator gets power but produces no steam. Also check the basics: make sure the water supply hose is connected and the valve is open, since a dry nozzle will produce no mist. Inspect the dryer nozzle at the back of the drum for clogs or damage that would block steam entry, and if the inlet valve does not open when energized, test it for continuity with a multimeter and replace it if it fails. If you need parts, enter your model number on RepairClinic.com to find the exact replacement part for your dryer and get step-by-step guidance for the repair.

01 - Maytag Dryer Control Board

If no power is getting to either the dryer's water inlet valve during the steam cycle or the steam generator, then it's likely the dryer's control board is defective and the cause of the steam function problem. The control board cannot be easily tested, but you can try to inspect it for signs of burning or a shorted-out component to help determine if the part should be replaced.
Enter model number to search for the required part specific to your product
Need help finding your model number?
Shop all Maytag Dryer Control Board Parts
Common

02 - Maytag Dryer Main Control Board

If no power is getting to either the dryer's water inlet valve during the steam cycle or the steam generator, then it's likely the dryer's main control board is defective and the cause of the steam function problem. The control board cannot be easily tested, but you can try to inspect it for signs of burning or a shorted-out component to help determine if the part should be replaced.
Shop all Maytag Dryer Main Control Board Parts
Common

03 - Maytag Dryer Steam Generator

If no power is getting to the dryer's water inlet valve during the steam cycle, but power is reaching the steam generator, then it's likely the steam generator is defective and will need to be replaced.
Shop all Maytag Dryer Steam Generator Parts
Common

04 - Water supply not connected.

The water supply hose needs to be connected from the home's water supply to the water inlet valve on the dryer. The water line is usually connected to a “Y” connector and shares the same cold-water supply as the washer. Refer to the owner's manual for water hookup instructions.
Common

05 - Maytag Dryer Nozzle

The nozzle, normally located at the rear interior of the dryer, may be damaged or clogged with debris and unable to allow the steam to enter the drum area. Inspect the nozzle or any damage or obstruction and replace if necessary.
Shop all Maytag Dryer Nozzle Parts
Less Common

06 - Maytag Dryer Water Inlet Valve

The dryer's water inlet valve provides the water necessary for the steam function to work. If there is no mist coming from the nozzle when the valve is energized, it's likely the inlet valve is defective. You can use a multimeter to test the valve for electrical continuity. If the valve tests negative for continuity, you'll know the part has failed and will need to be replaced.
Shop all Maytag Dryer Water Inlet Valve Parts
Less Common

07 - Water Supply Valves are Closed

The water supply valve needs to be turned on to supply water to the dryer. The water line is usually connected to a “Y” connector and shares the same cold-water supply as the washer. Refer to the owner's manual for water hookup instructions.
Less Common

Frequently Asked Questions

Why is my dryer steam function not working?
No mist during the steam cycle — how do I test the water inlet valve?
How can I tell if the steam generator or nozzle is the problem?
Could the control board be causing the steam feature to stop working?
How do I enter my model number or part number to find the correct replacement part on RepairClinic.com?