Choose Product
Identify Problem
03
Find Solutions
HomeRepair HelpHaier Dryer RepairHaier Dryer steam function not working Repair

Haier Dryer steam function not working

If your Haier dryer steam function is not working, the most likely culprit is the control board or main control board not sending power to the steam components. Start by checking the board for burnt components and whether it provides voltage to the water inlet valve and the steam generator. If the board is good but the steam generator gets power and still does nothing, the generator itself is probably bad. After that, confirm the water supply hose and Y-connector are hooked up and the inlet valve is actually being energized during a steam cycle. Inspect the rear nozzle for clogs or damage that would prevent mist from entering the drum, and if the nozzle is clear but no water flows when the valve is energized, use a multimeter to test the water inlet valve for continuity and replace it if it fails. Whether you need a control board, steam generator, nozzle or inlet valve, enter your model number on RepairClinic.com to find the exact replacement part for your dryer.

01 - Haier Dryer Control Board

If no power is getting to either the dryer's water inlet valve during the steam cycle or the steam generator, then it's likely the dryer's control board is defective and the cause of the steam function problem. The control board cannot be easily tested, but you can try to inspect it for signs of burning or a shorted-out component to help determine if the part should be replaced.
Enter model number to search for the required part specific to your product
Need help finding your model number?
Shop all Haier Dryer Control Board Parts
Common

02 - Haier Dryer Main Control Board

If no power is getting to either the dryer's water inlet valve during the steam cycle or the steam generator, then it's likely the dryer's main control board is defective and the cause of the steam function problem. The control board cannot be easily tested, but you can try to inspect it for signs of burning or a shorted-out component to help determine if the part should be replaced.
Shop all Haier Dryer Main Control Board Parts
Common

03 - Haier Dryer Steam Generator

If no power is getting to the dryer's water inlet valve during the steam cycle, but power is reaching the steam generator, then it's likely the steam generator is defective and will need to be replaced.
Shop all Haier Dryer Steam Generator Parts
Common

04 - Water supply not connected.

The water supply hose needs to be connected from the home's water supply to the water inlet valve on the dryer. The water line is usually connected to a “Y” connector and shares the same cold-water supply as the washer. Refer to the owner's manual for water hookup instructions.
Common

05 - Haier Dryer Nozzle

The nozzle, normally located at the rear interior of the dryer, may be damaged or clogged with debris and unable to allow the steam to enter the drum area. Inspect the nozzle or any damage or obstruction and replace if necessary.
Shop all Haier Dryer Nozzle Parts
Less Common

06 - Haier Dryer Water Inlet Valve

The dryer's water inlet valve provides the water necessary for the steam function to work. If there is no mist coming from the nozzle when the valve is energized, it's likely the inlet valve is defective. You can use a multimeter to test the valve for electrical continuity. If the valve tests negative for continuity, you'll know the part has failed and will need to be replaced.
Shop all Haier Dryer Water Inlet Valve Parts
Less Common

07 - Water Supply Valves are Closed

The water supply valve needs to be turned on to supply water to the dryer. The water line is usually connected to a “Y” connector and shares the same cold-water supply as the washer. Refer to the owner's manual for water hookup instructions.
Less Common

Frequently Asked Questions

Why is my dryer steam not working?
How can I check the water supply and nozzle for the steam function?
How do I test the dryer water inlet valve?
How can I tell if the control board or the steam generator is bad?
How do I enter my model number or part number on RepairClinic to get the right replacement part?