Unlock the Right Part
for Your Repair
Find the exact part you need
Enter your model number to see parts that fit your machine.
Choose Product
Identify Problem
03
Find Solutions
HomeRepair HelpHotpoint Dryer RepairHotpoint Dryer stopped spinning Repair
Hotpoint Dryer stopped spinning
When your Hotpoint dryer is not spinning and the drum has stopped turning, the most likely culprit is a broken drive belt. The belt wraps around the drum, idler pulley and motor, so if the drum spins easily by hand the belt is probably snapped and should be replaced. A faulty timer can also stop the drum, but that is rare, so check more common parts first. Confirm the power cord is plugged tightly into the outlet since intermittent or no power can make the dryer stop spinning. Obstructions in the blower wheel or a worn idler pulley can bind the drive system and prevent the drum from turning, so remove the vent and check airflow, clear any lint or trapped clothing, and verify the blower wheel and idler pulley spin freely. Finally, a failing drive motor can overheat and cut out during cycles; if the drum turns freely with the belt removed and the blower wheel is clear, the motor may need replacement. Enter your model number on RepairClinic.com to find the exact replacement drive belt, idler pulley, blower wheel, motor or timer for your dryer.
01 - Hotpoint Dryer Drive Belt
The drive belt is a very long, slender belt that wraps all the way around the dryer drum, around a tension pulley, and then around the drive motor pulley. Over time, the belt can break from normal use. If the belt is broken, the dryer won’t turn. To quickly determine if the belt is broken, reach into the dryer and turn the drum by hand. If the drum spins very easily, the belt is likely broken. Next, inspect the belt to confirm that it is broken. If the belt is broken, replace it.
Enter model number to search for the required part specific to your product
Top Solution
02 - Hotpoint Dryer Timer
A dryer drum that has stopped spinning unexpectedly could be caused by a faulty timer. However, this is very rarely the case. Before replacing the timer, check all the more commonly defective parts. If you determine that all of the other components are working properly, test the timer by using a multimeter and consulting the wiring diagram. If the timer is defective, replace it.
Top Solution
03 - Incoming Power Problem
Confirm the power cord is plugged tightly into the wall receptacle. A loose plug can provide intermittent power to the dryer and cause it to stop spinning during the cycle.
Top Solution
04 - Hotpoint Dryer Blower Wheel
The blower wheel works with the drive motor to draw air into the dryer drum. Clumps of lint, socks, and small articles of clothing can escape the lint filter and get caught in the blower wheel. Since the blower wheel is usually attached to the same drive motor shaft that drives the drum belt, an obstructed blower wheel may prevent the drum from spinning. To determine if the blower wheel is working properly, remove the dryer vent and assess the strength of the air flow. If the air flow is weak, check the blower wheel for obstructions. If no obstructions are present, try rotating the blower wheel by hand. If the blower wheel...
Common
05 - Hotpoint Dryer Idler Pulley
The dryer's idler pulley puts tension on the drive belt so the belt can rotate the drum during operation. A defective idler pulley can cause the dryer drum to stop spinning. Inspect the idler pulley and make sure it spins freely on the shaft. If the idler pulley is stuck, worn or damaged, we recommend replacing the drum drive belt in addition to replacing the idler pulley.
Common
06 - Hotpoint Dryer Drive Motor
The drive motor turns the drum and the blower wheel to exhaust the air. If the dryer runs, stops for a while, and then starts again, this likely indicates that the motor is overheating, causing the dryer to shut off until the motor cools down. First, remove the belt from the motor and check the blower wheel to ensure that it is not obstructed. Next, with the belt removed, try rotating the drum by hand. If the drum does not rotate freely, determine what is causing the drum to bind. If the drum turns freely and the blower wheel is clear of obstructions, the drive motor might be defective. If you suspect the motor is at fault...
Common
07 - Hotpoint Dryer Idler Assembly
The dryer's idler assembly puts tension on the drive belt so the belt can rotate the drum during operation. A defective idler assembly can cause the dryer drum to stop spinning. Inspect the idler pulley and make sure it spins freely on the shaft. If the idler pulley is stuck, worn or damaged, we recommend replacing the drum drive belt in addition to replacing the idler assembly.
Common
Frequently Asked Questions
Why is my dryer drum not turning?
My dryer starts then stops after a few seconds, what's causing it?
Dryer not starting or not turning on, what should I check first?
My dryer is making noise when the drum turns, what parts are usually to blame?
How do I enter my model number to find the correct replacement parts on RepairClinic.com?