Unlock the Right Part
for Your Repair
Find the exact part you need
Enter your model number to see parts that fit your machine.
Choose Product
Identify Problem
03
Find Solutions
HomeRepair HelpARDO Dryer RepairARDO Dryer won't start Repair
ARDO Dryer won't start
If your dryer won't start or is not turning on, the most likely cause is a blown thermal fuse—especially if the dryer stopped heating first—so check the fuse for continuity and inspect the exhaust vent for a restriction before replacing the part. Next, make sure the door is fully closed and nothing is blocking the latch, since a door that is not fully closed prevents the dryer from starting. If the dryer is completely dead with no clicks or hums, test the start switch with a multimeter; if there is no response the start switch could be bad. Listen for the door switch click when you close the door and test it for continuity if you don’t hear it. A faulty control board can also prevent the machine from powering the motor, so look for burnt components and verify voltage to the motor. Finally, check the blower wheel for an object or jammed clothing that can cause the motor to hum but not spin. Enter your model number on RepairClinic.com to find the exact replacement part for your dryer.
01 - ARDO Dryer Thermal Fuse
The thermal fuse is a safety device designed to protect the dryer from overheating. The fuse is located on the blower housing or at the dryer’s heat source such as the heating element on electric dryers or at the burner on gas models. The fuse should be closed for continuity meaning it has a continuous electrical path through it when good. If overheated the fuse will have no continuity meaning the electrical path is broken and the fuse has blown. A multimeter can be used to test it for continuity. Be aware that a blown thermal fuse is an indication of a restricted exhaust vent from the dryer to the outside. Always check t...
Enter model number to search for the required part specific to your product
Top Solution
02 - Door is not fully closed
Since the dryer will not start with the door open, confirm the door is fully closed and remove anything that is obstructing the door.
Top Solution
03 - ARDO Dryer Start Switch
To determine if the start switch is defective, attempt to start the dryer. If the dryer hums but does not start, the start switch is not at fault. If the dryer does not respond or make any noise, the start switch could be at fault. Use a multimeter to test the start switch for continuity. If the switch does not have continuity, replace it.
Highly Likely
04 - ARDO Dryer Door Switch
The door switch activates when the dryer door is closed. On most dryers, the door switch makes an audible clicking sound when it activates. To determine if the door switch is working, try starting your dryer and then listen for the “click.” If the door switch makes a clicking sound, it is probably not defective. If you don’t hear a click, use a multimeter to use the door switch for continuity. If the switch does not have continuity, replace it.
Common
05 - ARDO Dryer Control Board
A dryer's control board controls the voltage being sent to all of the appliance's electrical components. If the board is defective, it may not allow the dryer to start. You can inspect the board for signs of damage or a shorted component. You can also use a multimeter to test for voltage reaching the drive motor after reviewing the dryer's wiring diagram.
Common
06 - Object stuck in blower wheel
If the dryer won’t start, an article of clothing may have gotten past the lint screen and is caught in the blower wheel. When this happens the drive motor will either hum but won’t start or will make a lot of noise when trying to start. The blower cover will need to be removed to check for obstructions. If the blower wheel is damaged it will need to be replaced.
Common
07 - ARDO Dryer Heating Element
The heating element warms the air before it enters the dryer drum. Over time, the heating element can burn out, causing the dryer not to heat , or short out which can cause the dryer to overheat. To determine if the heating element is defective, use a multimeter to test it for continuity. If the heating element does not have continuity, or is shorted (has continuity to the case), replace it. Note: If the thermal fuse has tripped, some heating elements come with a thermal fuse and high limit thermostat already on them.
Common
Frequently Asked Questions
Why is my dryer not starting even though it has power?
My dryer hums but the drum won't turn, what should I check?
Can a blown thermal fuse make my dryer not start and why did it blow?
How do I test the start switch, door switch, and control board?
How do I enter my model number or part number on RepairClinic.com to find the correct replacement part?