Unlock the Right Part
for Your Repair
Find the exact part you need
Enter your model number to see parts that fit your machine.
Choose Product
Identify Problem
03
Find Solutions
HomeRepair HelpGE Dishwasher RepairGE Dishwasher stops mid-cycle Repair
GE Dishwasher stops mid-cycle
If your GE dishwasher stops mid-cycle, the most likely problem is a failed or clogged water inlet valve. When that valve cannot open for the next fill, the dishwasher stops during cycle after the sump drains. Next, check the door latch, since a worn or damaged latch or door switch can tell the control board the door is open and shut the cycle down. If your GE dishwasher shuts off mid-cycle and shows a code, fault codes can point you to the exact failure faster than guesswork. A bad control board is another common cause because it powers nearly every electrical component. If the unit fills but then just hums, won’t wash, or the dishwasher cycle stops before finished, the circulation pump or the pump and motor assembly may be failing, blocked by debris, or have a damaged impeller. On RepairClinic.com, you can enter your model number to find the exact GE replacement part for your dishwasher, whether you need a water inlet valve, door latch, control board, circulation pump, or pump and motor assembly.
01 - GE Dishwasher Water Inlet Valve
The water inlet valve opens to allow water to enter the dishwasher. If the water valve fails, the dishwasher will stop in mid-cycle after the remaining water in the sump area has drained prior to the fill cycle. The water inlet valve coil can be tested for electrical continuity to help determine if the part is faulty. The valve could also be clogged. A clogged valve can not be cleaned and should be replaced.
Enter model number to search for the required part specific to your product
Highly Likely
02 - GE Dishwasher Door Latch
The dishwasher door needs to be properly latched for the appliance to work. If the latch is faulty, the door switch could signal the control board to stop the dishwasher in mid-cycle. Inspect the door latch for any damage and replace if necessary.
Common
03 - Check Fault Codes
If the dishwasher stop mid-cycle, a fault code will usually be displayed to help diagnose the issue. Refer to the owner's manual or do an on-line search to find out more information regarding what the fault code means.
Common
04 - GE Dishwasher Touchpad
A stuck button or damaged touchpad could result in the dishwasher stopping mid-cycle. To determine if the touchpad is at fault, try pressing various buttons on the touchpad. If some of the buttons don’t respond, the touchpad might be defective. (Some manufacturers sell the touchpad separately from the control panel. Other manufacturers require that you purchase the touchpad and control panel together. If you cannot replace the touchpad individually, replace the touchpad and control panel.)
Common
05 - GE Dishwasher User Control and Display Board
A dishwasher's user control and display board allows the user to select a wash and drying cycle and start the appliance. If the component is defective, it may cause the dishwasher to stop mid-cycle. Try pressure various buttons on the control to see if they all respond correctly. If some buttons work but others don't, it's likely the user control and display board is faulty and will need to be replaced with a new one.
Common
06 - GE Dishwasher Circulation Pump
The circulation pump uses a motor and impeller to force water up through the wash arms. If the circulation pump is defective, the dishes won’t be cleaned properly. If the motor isn’t making any noise or is just making a humming sound after the dishwasher has filled, the motor may be burned out. First, ensure that power is getting to the motor. Second, to ensure that the impeller can turn, check the pump housing for debris. If power is getting to the motor and the pump is clear of debris, the motor might need to be replaced. Be aware that the circulation pump may be challenging to replace, although many do-it-yourselfers ha...
Common
07 - GE Dishwasher Pump and Motor Assembly
The motor drives an impeller to force water up through the wash arms. If the motor is defective, the pump impeller is broken, or some part of the pump is clogged, dishes won’t be cleaned properly. Make sure that power is getting to the circulation pump and motor. If power is getting to the pump and motor assembly but it still won’t run, replace the pump and motor assembly.
Common
Frequently Asked Questions
Why does my GE dishwasher stop mid-cycle?
How do I know if the water inlet valve is causing my GE dishwasher to stop during the cycle?
Can a bad door latch make a GE dishwasher shut off mid-cycle?
My GE dishwasher has power but stops mid-cycle and hums. Is the circulation pump bad?
How do I find the right GE dishwasher part for a mid-cycle stopping problem?