In-stock parts ship the same day
Price Match Guarantee
In-stock parts ship the same dayGET PRO PRICING
Video & Articles: Appliance & Equipment RepairFrigidaire Top Load Washer Drain Pump Replacement #137221600
Frigidaire Top Load Washer Drain Pump Replacement #137221600
Skill Level
Total Parts Cost
$161.38Estimated Savings
$112.5002:50
- Description
This video provides step-by-step instructions for replacing the drain pump on Frigidaire top loading washing machines. The most common reasons for replacing the drain pump are when the washer won’t drain and the pump or drain isn’t simply clogged by a small sock or other item of clothing, or when the washer leaks water.
All of the information in this drain pump replacement video is applicable to the following brands: Frigidaire, Westinghouse, Kenmore, Gibson, Crosley, Universal, Electrolux, Tappan
All of the information in this drain pump replacement video is applicable to the following brands: Frigidaire, Westinghouse, Kenmore, Gibson, Crosley, Universal, Electrolux, Tappan
Step By Step Instructions
1
As with any repair, you should unplug the appliance before beginning.
2
To replace the drain pump on your washer, you should first secure the lid with tape.
3
Now insert a putty knife under the main top to release the two spring clips.
4
Lift up the main top and support it.
5
Next, remove the mounting screws at the bottom of the front panel.
6
Push the panel down and pull it away from the frame.
7
Now disconnect the wire harness from the drain pump and unhook the wires from the retaining clip.
8
Release the clamps securing the inlet and drain hoses to the pump…
9
…and pull the hoses off.
10
Be prepared for some water to spill out.
11
Remove the mounting screws securing the pump to the base…
12
…and pull the old pump out.
13
Install the new drain pump…
14
…by aligning it on the base…
15
…and securing it with the mounting screws
16
Connect the inlet and drain hoses to the new pump…
17
…and secure the clamps.
18
Connect the wire harness to the new pump and secure the wires under the retaining clip.
19
Replace the front panel by…
20
…aligning the tabs on the panel with the slots in the frame…
21
…then lift the panel up.
22
Replace the mounting screws to secure.
23
Remove the support…lower the main top…
24
…and snap it into place.
25
Then remove the tape securing the lid.
26
You’re now ready to plug the power cord back in…
27
…and confirm that the washer is functioning properly.
Description
This video provides step-by-step instructions for replacing the drain pump on Frigidaire top loading washing machines. The most common reasons for replacing the drain pump are when the washer won’t drain and the pump or drain isn’t simply clogged by a small sock or other item of clothing, or when the washer leaks water.
All of the information in this drain pump replacement video is applicable to the following brands: Frigidaire, Westinghouse, Kenmore, Gibson, Crosley, Universal, Electrolux, Tappan
All of the information in this drain pump replacement video is applicable to the following brands: Frigidaire, Westinghouse, Kenmore, Gibson, Crosley, Universal, Electrolux, Tappan
Step-By-Step Instructions
1
As with any repair, you should unplug the appliance before beginning.
2
To replace the drain pump on your washer, you should first secure the lid with tape.
3
Now insert a putty knife under the main top to release the two spring clips.
4
Lift up the main top and support it.
5
Next, remove the mounting screws at the bottom of the front panel.
6
Push the panel down and pull it away from the frame.
7
Now disconnect the wire harness from the drain pump and unhook the wires from the retaining clip.
8
Release the clamps securing the inlet and drain hoses to the pump…
9
…and pull the hoses off.
10
Be prepared for some water to spill out.
11
Remove the mounting screws securing the pump to the base…
12
…and pull the old pump out.
13
Install the new drain pump…
14
…by aligning it on the base…
15
…and securing it with the mounting screws
16
Connect the inlet and drain hoses to the new pump…
17
…and secure the clamps.
18
Connect the wire harness to the new pump and secure the wires under the retaining clip.
19
Replace the front panel by…
20
…aligning the tabs on the panel with the slots in the frame…
21
…then lift the panel up.
22
Replace the mounting screws to secure.
23
Remove the support…lower the main top…
24
…and snap it into place.
25
Then remove the tape securing the lid.
26
You’re now ready to plug the power cord back in…
27
…and confirm that the washer is functioning properly.
Applicable Product Model
Parts Needed
Drain Pump
$161.38
Total$0.00
Related Articles & Videos