Order by 2:00 a.m., and we'll ship the same day
Price Match Guarantee
Order by 2:00 a.m., and we'll ship the same dayGET PRO PRICING
Video & Articles: Appliance & Equipment RepairKitchenAid Garbage Disposer Mounting Ring Replacement 4211306 
KitchenAid Garbage Disposer Mounting Ring Replacement 4211306
Skill Level
Total Parts Cost
$6.88Estimated Savings
$112.5003:50
- Description
This video provides step-by-step repair instructions for replacing the mounting ring on a KitchenAid garbage disposer. The most common reason for replacing this part is if it is damaged or missing.
All of the information for this replacement video is applicable to the following brands:
KitchenAid
All of the information for this replacement video is applicable to the following brands:
KitchenAid
Step By Step Instructions
1
KitchenAid Garbage Disposer - KCDB250G4
2
KitchenAid Garbage Disposer Mounting Ring Replacement
3
Tools needed: 3/8th inch nut driver, flat-head screwdriver
4
Shock
5
Before you begin the procedure, unplug the unit?s power cord.
6
Water
7
If there is not enough slack, detach the dishwasher?s drain hose from the disposer inlet port, if applicable.
8
Using the 3/8th inch nut driver or the flat-head screwdriver, unthread the two mounting screws securing the tailpipe flange to the disposer.
9
Heavy
10
Now rotate the lock ring counter-clockwise to release the disposer from the sink.
11
Next, use the flat-head screwdriver to loosen the three screws securing the mounting bracket to the strainer flange.
12
With the screws loosened, lift the bracket up and use the screwdriver to pry the old mounting ring free of the strainer flange if still intact.
13
Before you install the new mounting ring, confirm the mounting bracket screws are partially unthreaded.
14
Align the flange mounting plate on the bracket followed by the lower sink flange seal.
15
Align the mounting ring on the bottom, then, holding the components together, position them on the bottom of the strainer flange.
16
Push the bracket up while pushing down on the strainer flange, then snap the mounting ring into place in the strainer flange groove.
17
With the ring secured, tighten all three screws.
18
Reinstall the disposer by positioning it in the mounting bracket, making sure the disposer?s outlet port is aligned with the tailpipe.
19
Confirm the tailpipe gasket is in place on the outlet port, then position the tailpipe flange with the port and thread the two screws to secure.
20
Now fully rotate the disposer lock ring clockwise until it locks into place.
21
If applicable, reattach the dishwasher?s drain hose to the inlet port.
22
Plug the power cord back in and the garbage disposer should be ready for use.
Description
This video provides step-by-step repair instructions for replacing the mounting ring on a KitchenAid garbage disposer. The most common reason for replacing this part is if it is damaged or missing.
All of the information for this replacement video is applicable to the following brands:
KitchenAid
All of the information for this replacement video is applicable to the following brands:
KitchenAid
Step-By-Step Instructions
1
KitchenAid Garbage Disposer - KCDB250G4
2
KitchenAid Garbage Disposer Mounting Ring Replacement
3
Tools needed: 3/8th inch nut driver, flat-head screwdriver
4
Shock
5
Before you begin the procedure, unplug the unit?s power cord.
6
Water
7
If there is not enough slack, detach the dishwasher?s drain hose from the disposer inlet port, if applicable.
8
Using the 3/8th inch nut driver or the flat-head screwdriver, unthread the two mounting screws securing the tailpipe flange to the disposer.
9
Heavy
10
Now rotate the lock ring counter-clockwise to release the disposer from the sink.
11
Next, use the flat-head screwdriver to loosen the three screws securing the mounting bracket to the strainer flange.
12
With the screws loosened, lift the bracket up and use the screwdriver to pry the old mounting ring free of the strainer flange if still intact.
13
Before you install the new mounting ring, confirm the mounting bracket screws are partially unthreaded.
14
Align the flange mounting plate on the bracket followed by the lower sink flange seal.
15
Align the mounting ring on the bottom, then, holding the components together, position them on the bottom of the strainer flange.
16
Push the bracket up while pushing down on the strainer flange, then snap the mounting ring into place in the strainer flange groove.
17
With the ring secured, tighten all three screws.
18
Reinstall the disposer by positioning it in the mounting bracket, making sure the disposer?s outlet port is aligned with the tailpipe.
19
Confirm the tailpipe gasket is in place on the outlet port, then position the tailpipe flange with the port and thread the two screws to secure.
20
Now fully rotate the disposer lock ring clockwise until it locks into place.
21
If applicable, reattach the dishwasher?s drain hose to the inlet port.
22
Plug the power cord back in and the garbage disposer should be ready for use.
Applicable Product Model
Parts Needed
Mounting Ring
$6.88
Total$0.00
Related Articles & Videos
04:09
Part Replacement
KitchenAid Garbage Disposer Upper Sink Flange Seal Replacement WP4211302