In-stock parts ship the same day
Price Match Guarantee
In-stock parts ship the same dayGET PRO PRICING
Video & Articles: Appliance & Equipment RepairFrigidaire Dishwasher Control Board Replacement (part 5304520582)
Frigidaire Dishwasher Control Board Replacement (part 5304520582)
Skill Level
Total Parts Cost
$147.38Estimated Savings
$112.5004:31
- Description
This video provides step-by-step repair instructions for replacing the control board on Frigidaire dishwasher model #FGID2466QF7A. The most common reason for replacing the board is if the dishwasher won’t start.
All of the information for this control board replacement video is applicable to the following brands: Frigidaire & Electrolux
Tools needed: Phillips-head screwdriver & a T-20 Torx bit.
All of the information for this control board replacement video is applicable to the following brands: Frigidaire & Electrolux
Tools needed: Phillips-head screwdriver & a T-20 Torx bit.
Step By Step Instructions
1
Frigidaire Dishwasher - Model FGID2466QF7A
2
Dishwasher Control Board Replacement
3
Tools Needed
4
You will need a phillips-head screwdriver and a T-20 Torx bit for this procedure.
5
Be sure to turn off the power to the appliance.
6
Open the door and use a phillips-head screwdriver to unthread all four screws securing the outer door panel.
7
"With the screws unthreaded, you can pull the panel down to detach."
8
"Using a T-20 Torx bit, unthread the six screws securing the control panel assembly."
9
"Using the phillips-head screwdriver, unthread the two screws securing the control board cover."
10
Pull back the retainers to release the cover tab and detach the wiring grommet.
11
Disconnect the user interface assembly wire harness from the control board as well as the display board wire harness.
12
"Note the orientation of the remaining wire connecters connected to the control board, then disconnect them."
13
Unthread the mounting screws to release the old board.
14
You’re now ready to install the new control board.
15
"Confirm that the seal is in place on the control panel, then position the new board."
16
Thread the mounting screws.
17
Connect all of the wire connecters to the appropriate terminals on the new board.
18
Position the wiring grommet in the control board cover then snap the cover into place.
19
Thread the two mounting screws.
20
Realign the control panel assembly and secure it with the screws.
21
Reinstall the outer door panel by aligning it on the inner panel then slide up.
22
Thread the four mounting screws to secure.
23
Turn the power supply back on.
24
Congrats! Your dishwasher is ready for use.
Description
This video provides step-by-step repair instructions for replacing the control board on Frigidaire dishwasher model #FGID2466QF7A. The most common reason for replacing the board is if the dishwasher won’t start.
All of the information for this control board replacement video is applicable to the following brands: Frigidaire & Electrolux
Tools needed: Phillips-head screwdriver & a T-20 Torx bit.
All of the information for this control board replacement video is applicable to the following brands: Frigidaire & Electrolux
Tools needed: Phillips-head screwdriver & a T-20 Torx bit.
Step-By-Step Instructions
1
Frigidaire Dishwasher - Model FGID2466QF7A
2
Dishwasher Control Board Replacement
3
Tools Needed
4
You will need a phillips-head screwdriver and a T-20 Torx bit for this procedure.
5
Be sure to turn off the power to the appliance.
6
Open the door and use a phillips-head screwdriver to unthread all four screws securing the outer door panel.
7
"With the screws unthreaded, you can pull the panel down to detach."
8
"Using a T-20 Torx bit, unthread the six screws securing the control panel assembly."
9
"Using the phillips-head screwdriver, unthread the two screws securing the control board cover."
10
Pull back the retainers to release the cover tab and detach the wiring grommet.
11
Disconnect the user interface assembly wire harness from the control board as well as the display board wire harness.
12
"Note the orientation of the remaining wire connecters connected to the control board, then disconnect them."
13
Unthread the mounting screws to release the old board.
14
You’re now ready to install the new control board.
15
"Confirm that the seal is in place on the control panel, then position the new board."
16
Thread the mounting screws.
17
Connect all of the wire connecters to the appropriate terminals on the new board.
18
Position the wiring grommet in the control board cover then snap the cover into place.
19
Thread the two mounting screws.
20
Realign the control panel assembly and secure it with the screws.
21
Reinstall the outer door panel by aligning it on the inner panel then slide up.
22
Thread the four mounting screws to secure.
23
Turn the power supply back on.
24
Congrats! Your dishwasher is ready for use.
Applicable Product Model
Parts Needed
Control Board
$147.38
Total$0.00
Related Articles & Videos
08:11
Part Replacement
Frigidaire Dishwasher Sump Housing Gasket Replacement (part 154246801)